Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 44

Страница: 44 / 86

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Troubleshooting Manual

Chapter 8

8.1.9 Mount and secure the operator to the

attachment bracket.

1. Adhere 3 pieces of felt at equal distances onto the

attachment bracket.

2. The openings of the door panel suspension must

point to the front.

3. When using MANET attachments, the door panel

suspensions must be removed.

4. Fasten the operator below the attachment bracket

with 6 hexagon screws (lock screws)
Torque: 5.9 ft lb [8 Nm].

8.1.10 Connection of 120 Vac permanent power

supply.

WARNING

Work on electrical equipment must only be
performed by properly qualified personnel
(electricians).
Before starting installation, make sure that
the 120 Vac power supply is OFF.

1. Loosen the end stop and move it to the center of the

system (Ref. Chapter 7, Fig. 7.3).

2. Cut the wires to length, strip the wire insulation

(1/4" [6 mm]).

3. Connect L1 and N to the terminals of the power

supply.

4. Reference Para.8.1.12 for grounding wire connection.

8.1.11 Conduit

connection.

When using a conduit connection, use the supplied
conduit cover, mounting plate and Phillips screws.

1. Attach mounting plate to operator with 2 screws.

2. Route the wires through the mounting plate and

connect to the operator.

3. Fold the conduit cover as shown.

4. Secure conduit cover to mounting plate with

remaining screw.

8.1.12 Grounding wire (PE) connection to power supply.

1. Using a screwdriver, open the control unit housing

cover.

2. Route the grounding wire through the operator

control unit housing and connect it to the grounding
terminal (PE).

WARNING

The grounding wire must be connected to the
PE terminal.

8.1.13 Connection of external accessories.

1. Connect all external accessories except for safety

sensors. Refer to cable channel instructions.

Fig. 8.1.12 Mounting operator to attachment bracket

Fig. 8.1.13 Connection of 120 Vac permanent power supply

6”

[150 mm]

1/4”

[6 mm]

1 3/8”

[35 mm]

1/4”

[6 mm]

Fig. 8.1.14 Conduit connection

Fig. 8.1.15 Grounding wire (PE) connection to power supply

Содержание CS 80 MAGNEO























































































Результаты поиска

Содержание CS 80 MAGNEO

Отзывы:

Dormakaba CS 80 MAGNEO, Инструкция по установке и устранению неисправностей, Страница: 44 / 86

Результаты поиска

Содержание CS 80 MAGNEO

Отзывы: