Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 86

Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 32

32

CS 80 MAGNEO

10-2022

DL3316-010

Chapter 4

Installation and Troubleshooting Manual

4 Safety instructions

4.1 Specified standard operation.

WARNING

The CS 80 MAGNEO is only designed to open
and close doors.
Do not allow children to play with the CS 80
MAGNEO or rigidly mounted adjustment and/or
control devices. Keep remote controls out of
reach of children.

4.2 Product-specific

characteristics.

The CS 80 MAGNEO is intended for use on interior
single panel sliding doors.

The CS 80 MAGNEO is not suitable for application in
escape routes, on fire or smoke doors, or on exterior
doors.

4.3 Standards, codes and regulations.

The CS 80 MAGNEO is a low energy product and
complies with the kinetic force limitations of
ANSI/BHMA A156.10, A156.19 and A156.38
Low Energy Standards.

WARNING

Danger spots at closing edges.

Automatic doors may cause hazards by
crushing, shearing, hitting and drawing-in at the
different closing edges.

Main

closing edge

Secondary
closing edge

Systems with CS 80 MAGNEO offer the following
benefits:

• The system does not have to be equipped with

additional protection equipment.

• The application of safety sensors at the closing

edges as an additional protection measure is
optional and lies in the discretion of the person
performing the installation of the door system under
consideration of the result of the individual risk
assessment.

Special spatial conditions and certain user groups might
make it sensible to equip the application with safety
sensor even when the system is operated in the Low
Energy Mode.
Whether this is required or not has to be assessed with
the aid of an individual risk assessment and must be
considered during the planning of the system and by the
manufacturer, i.e. the party performing the installation
of the system. We would therefore ask you to have a
look at our risk assessment form, which is available at
www.dormakaba .com.
Special requirements regarding the protection of people
in need of protection. In case the risk assessment
reveals that there is a health risk of injury when the
door hits a user in an unacceptable way, additional
protection via safety equipment (connection of safety
sensors) is required. This is especially necessary when
people in need of protection (children, elderly people or
disabled use the door.

4.4 Limitation of liability.

The CS 80 MAGNEO must only be used according to its
specified standard operation.
dormakaba will not accept any liability for damages
resulting from unauthorized modifications, unsafe or
improper installation or use of the CS 80 MAGNEO.

«
...
30
31
32
33
34
...
»

Содержание CS 80 MAGNEO























































































Отзывы:

Нет отзывов