Dormakaba CS 80 MAGNEO Скачать руководство пользователя страница 56

Страница: 56 / 86

CS 80 MAGNEO

10-2022

DL3316-010

Installation and Troubleshooting Manual

Chapter 12

12 Connection of closing edge protection

CAUTION

This work must only be performed by
qualified, trained persons.

NOTICE

Main closing edge:

The leading edge of the

door.
Activating the sensor will disable automatic
operation in the closing direction.

Secondary closing edge:

The trailing edge of

the door.
Activating the sensor will disable automatic
operation in the opening direction.

When testable sensors for the protection of the closing
edge are connected, the control unit has to be
configured to the sensors via the DIP switches.

Main closing edge sensor connection:

• Set DIP switch 1 to ON and DIP switch 2 to OFF.

Secondary closing edge sensor connection:

• Set DIP switch 1 to ON and DIP switch 3 to OFF.

Sensors connected to both main and secondary closing
edges:

• Set DIP switch 1 to ON and DIP switches 2 and 3 to

OFF.

Fig. 12.1.1

Control unit DIP switch

Test high active

OFF

Test low active

Sensor test for secondary closing edge activated

OFF

Sensor test for secondary closing edge deactivated

Sensor test for main closing edge activated

OFF

Sensor test for main closing edge deactivated

Table 12.1.1 Closing edge sensors

DIP switch settings

Содержание CS 80 MAGNEO























































































Результаты поиска

Содержание CS 80 MAGNEO

Отзывы:

Dormakaba CS 80 MAGNEO, Инструкция по установке и устранению неисправностей, Страница: 56 / 86

Результаты поиска

Содержание CS 80 MAGNEO

Отзывы: