208
i-
α
pp
li
Launching i-
α
ppli from a site
When an i-
α
ppli software launch specification is
displayed on an i-mode site, this setting allows the
software to be launched from the site.
z
This function cannot be used with some sites.
1
Sites screen (p.146) Select an item for
launching the software “YES”
Launching i-
α
ppli from a mail
When an i-
α
ppli software launch specification is
pasted into a received i-mode mail, this setting allows
the software to be launched from the i-mode mail.
1
Received mail detail screen (pp.180,
182) Select an item for launching the
software “YES”
Launching i-
α
ppli from other
functions
You can launch an i-
α
ppli from various functions such
as Infrared data exchange function, Bar code reader,
IC card function or ToruCa.
■
Infrared data exchange function
When the FOMA terminal received the i-
α
ppli
launching signal while Infrared data exchange, i-
α
ppli
software launches.
■
Bar code reader
When the data scanned by the Bar code reader
contains an i-
α
ppli software launch specification, you
can launch the software from the Bar code reader.
■
IC card function
You can launch the software by holding the FeliCa
mark on the FOMA terminal over the reader/writer
unit.
■
ToruCa
When an i-
α
ppli software launch specification is
pasted into an acquired ToruCa, you can launch the
software from ToruCa.
Setting the i-
α
ppli Standby
Screen
<Set i-
α
ppli stand-by>
You can set a selected i-
α
ppli software as the standby
screen.
z
Some software applications cannot be set as the
standby screen.
1
Software list screen (p.197)
o
(Set)
“Stand-by display” “ON”
o
(Finish)
Activating the i-
α
ppli standby screen
You can activate the software set as the i-
α
ppli
standby screen.
1
On the i-
α
ppli standby screen
t
The i-
α
ppli is activated and
or
flashes
at the bottom of the screen.
N
z
Unlike ordinary i-
α
ppli, some i-
α
ppli software is
immediately launched from an i-mode site.
• These i-
α
ppli are not stored on the FOMA terminal
after downloading from i-mode sites,
• Some i-
α
ppli software cannot be stored on the
FOMA terminal.
N
z
The i-
α
ppli launch specification cannot be quoted
even when you reply with a quote or forward the
i-mode mail. You cannot quote a launch specification
of an i-
α
ppli by forwarding mail using the Infrared data
exchange function or DoCoMo keitai datalink (p.326),
etc.
N
<IC card function>
z
The software is not launched in the following cases:
• When another function is running
• During calls
• When the software you want to launch cannot be
found
N
z
Only 1 i-
α
ppli can be set as the i-
α
ppli standby screen.
z
If software that communicates is set as the standby
screen, it may not run correctly when problems such
as poor signal quality occur.
z
If you select “OFF” for “Stand-by net” in “Software
setting”, note that you may not be able to receive
timely information.
z
If “Dial lock” or “Original lock” is set or 2in1 is set to B
mode or Dual mode while the i-
α
ppli standby screen is
displayed, the i-
α
ppli standby screen ends. If “Dial
lock” or “Original lock” is released or 2in1 is set to A
mode, the i-
α
ppli standby screen reappears.
z
When you switch tasks and display the standby
screen, the screen specified in “Stand-by display” of
“Display setting” appears even though the i-
α
ppli
standby screen is set.
Содержание foma SO705i
