Dini Argeo 3590 EBOX Series Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 132

Dini Argeo 3590 EBOX Series Скачать руководство пользователя страница 51

3590EKR, 3590EXP, 3590EXT, 3590 EBOX, CPWE, CPWET series indicator E-AF03_05.01_14.07_EN_T.doc

51

<< inPutS >>

INPUT TEST

By pressing

ENTER

it’s possible to test the status of the inputs; the display will show:

in which the number on the first line identifies the input:

1

IN1

Inputs of the motherboard

2

IN2

3

IN3

…

Inputs of the expansion board

8

IN8

and the number each input corresponds to its status:

0 = disabled;
1 = enabled.

<< Anout >>

ANALOGUE OUTPUT

If the instrument is fitted with the analogue output, through this step one can test if the values of the D/A converter (to be
entered at time of calibration) correspond with the relative values of the analogue output (in voltage or in current), see
section 6.

By pressing

ENTER

the display shows 0; enter a value between 0 and 65535 and confirm with

ENTER

; the instrument

will supply the corresponding analogue value in output.
To exit the test confirm twice with

ENTER

the same entered value.

<< SEr. >>

SERIAL PORTS TEST

By pressing

ENTER

it’s possible to redirect the data received by any serial port, on other serial ports.

<< SEr.nuM >>

SERIAL NUMBER

Diagnostics check for use of the manufacturer.

<< P.teSt >>

PRINT TEST

With this feature you can print all print formats of the instrument. By pressing ENTER the step it is asked which format to

print. If you enter the 0 value, all print formats are printed in sequence.

<< nEt.VEr >>

NET FIRMWARE VERSION

This step shows the version of the net firmware (SETH). If the SETH device was not found the message "SETH DEVICE

NOT FOUND" is displayed, otherwise the version is displayed in the form:
"NET FW VERSION"
"01.02.05.0036" (present version)

<< EU.LoG >>

EVENT LOG VIEWER

The instrument stores the following types of events:
- Metric event (calibration, equalization)

- Battery event (on, off, change of power, ...)
- Keyboard event (pressed keys)
- Setup event (by default, to restore from backup, save setup, ...)
- Firmware update event (firmware update)

For each type of event the last 10 events are stored with date/time In the function you can select what type of event is
displayed and scroll the last 10 events. The F5 key is to be pressed in order to print the list.

INPUTS

1 2 3 4 5 6 7 8

0 0 0 0 0 0 0 0

«
...
49
50
51
52
53
...
»

Содержание 3590 EBOX Series





































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды