Dini Argeo 3590 EBOX Series Скачать руководство пользователя страница 38

Страница: 38 / 132

3590EKR, 3590EXP, 3590EXT, 3590 EBOX, CPWE, CPWET series indicator E-AF03_05.01_14.07_EN_T.doc

(!) None

Word

SET WORD

By pressing

ENTER

one can select the number of data bits. The possible values are: 8 (8 data bits) and 7 (7 data

bits).

(!) 8 bit

StoP b

SET STOP BIT

By pressing the

ENTER

key one can then select the number of stop bits. The possible values are: 1 (1 stop bit) and

2 (2 stop bits).

(!) 1 bit

<< CtS.St. >>

SYNCHRONISM SIGNAL

Not used in this application.

<< ProtoC >>

SELECTS PROTOCOL

nonE

no protocol

Cont.

continuous transmission

riPE 6

Dini Argeo

6-digit repeater.

riPEdC

DC Repeater

Eth.nEt

protocol Ethernet

Coin

coin

(!) nonE

<< rEM.SCA

REMOTE SCALE CONFIGURATION

(*)(§)

This step allows setting the parameters for managing a remote scale

(*)

In case of approved instrument the step is not visible.

(§)

It’s possible to enable the remote scale only if the

SEtuP >>

SEriAL >> rEAdEr

parameter has not been set on

“

CoMAuX

”.

<< EnAb. >>

ENABLING REMOTE SCALE

Selection/unselection of the remote scale functioning mode:

ENABLED

DISABLED

(!) DISABLED

<< tErM >>

REMOTE SCALE TERMINATOR

In this step one enters the ASCII decimal code (up to 2 characters) of the terminator characters of the weight
string (I.E. 13 for CR or 10 for LF).

(!) 000

<< WEi.PoS >>

REMOTE SCALE WEIGHT POSITION

In this step one sets the position of the first character of the weight value in the string transmitted by the remote

scale, knowing that the first character on the left of the string has the 00 position.
A sign is part of the weight value.
For example, if the received string is

sppp CR + LF:

Received string

CR LF

Position of the
character

Therefore one should set the value 00.
It is possible to set up to 2 characters (from 0 to 99).

(!) 00

<< WEi.LEn >>

LENGTH OF THE WEIGHT DATA STRING

In this step one enters the number of digits (from 1 to 99) which make up the weight value, including the sign and

Содержание 3590 EBOX Series





































































































































Результаты поиска

Содержание 3590 EBOX Series

Отзывы:

Бренды по названию

Популярные бренды

Dini Argeo 3590 EBOX Series, Техническое руководство

Результаты поиска

Содержание 3590 EBOX Series

Отзывы:

Бренды по названию

Популярные бренды