Dini Argeo 3590 EBOX Series Скачать руководство пользователя страница 37

Страница: 37 / 132

3590EKR, 3590EXP, 3590EXT, 3590 EBOX, CPWE, CPWET series indicator E-AF03_05.01_14.07_EN_T.doc

(like a printer) that is slow in processing the data received, can interrupt the transmission temporarily using this

signal.
It is possible to select:

NO.CTS

Disable

LOW

CTS active low

HIGH

CTS active high

EMUCTS

Emulation of CTS signal: one is asked to enter the number of characters (nChrS) using 3 digits, which

will be transmitted upon each transmission; then one should enter the wait time in milliseconds (tiME),
using 4 digits, from a transmission and the next one.

(!) NO.CTS

Add.485

485 ADDRESS

By pressing

ENTER

it is possible to enter a 2 digit code (from 00 to 98) which identifies the instrument from the

ones connected in the RS485 transmission mode.

NOTE:

the 99 code is used as a broadcast address.

(!) 00

<< ProtoC >>

SELECTS PROTOCOL

StAnd

Standard

AFXX

AF0X

riPE 6

Dini Argeo

6-digit repeater

riPLCd

LCD repeater (for 3590E version)

Mondir

Uni-directional

ALibi

Alibi memory

SMA

SMA protocol

ModbuS

Modbus protocol

Profi.b

Profibus protocol

b tYPE

riP. b
Eth.nEt

protocol Ethernet

riP.b3

riP.b4

Coin

coin

For the protocol specifications, see section 5.4

(!) StAnd

PC.ModE

TRANSMISSION TYPE

rEquE.

On request

Cont.

Continuous

StAbiL

On stability

- 485 -

485 mode

End.CYC

At the end of the in/out weighing cycle or of the single weigh.

For the transmission mode specifics, see section 5.5

(!) rEquE.

<< CoMAuX >>

AUX SERIAL CONFIGURATION

bAud

SET BAUD RATE

By pressing

ENTER

one can select the data transmission speed (measured in Baud = bit/second). The possible

values are: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200.

(!) 9600

<< PAritY

SET PARITY

By pressing

ENTER

one can select the parity bit type. The possible values are: None (absent parity bit), Odd

(uneven parity bit) and Even (even parity bit).

Содержание 3590 EBOX Series





































































































































Результаты поиска

Содержание 3590 EBOX Series

Отзывы:

Бренды по названию

Популярные бренды

Dini Argeo 3590 EBOX Series, Техническое руководство

Результаты поиска

Содержание 3590 EBOX Series

Отзывы:

Бренды по названию

Популярные бренды