Dini Argeo 3590 EBOX Series Скачать руководство пользователя страница 41

Страница: 41 / 132

3590EKR, 3590EXP, 3590EXT, 3590 EBOX, CPWE, CPWET series indicator E-AF03_05.01_14.07_EN_T.doc

<< ZEro >>

TRANSMISSION OF SCALE ZERO COMMAND FROM THE INDICATOR

In this step one can enable the Zero scale transmission command: the command (not configurable) is

followed by

a “CR”.

DISABLED

ENABLED

(!) DISABLED

<< tArE >>

REMOTE SCALE TARE SENDING

In this step one can enable the transmission of the Tare command from the indicator:

DISABLED

ENABLED

>> One will be requested to enter the command that is to be transmitted (up to 3 alphanumeric

characters) followed by a “CR”.

(!) DISABLED

<< MAn.tAr >>

REMOTE SCALE MANUAL TARE

In this step one can enable the transmission of the manual Tare command from the indicator:

Disable

disabled

VAL.CMd

first the value is transmitted and then the tare command

CMd.VAL

first the command is transmitted and then the tare value

If one sets

VAL.CMd

CMd.VAL

one will be asked to enter the command to be transmitted (up to 3 alphanumeric

characters) followed by a “CR”.

(!) Disable

<< rEq.WEi >>

REMOTE SCALE WEIGHT REQUEST

In this step one can enable the serial command which will be used to request the string from the remote scale,
when it is transmitted upon request.

DISABLED

ENABLED

>> It will be possible to set the request interval (001..up to 255 sec) and the serial command for

reading the weight (up to 4 alphanumeric characters).

(!) DISABLED

NOTE:

For the scale configuration of the remote scale, refer to the relative manual.

<< rEAdEr >>

READER PROTOCOL

Enabling data reception from external reader (See relative manual)

DISABLE

data reception disabled

COM.AUX

protocol enabled on the ComAux

COM.PRN

protocol enabled on the ComPrn

(!) DISABLE

<< r71.rEP >>

R71 REPEATER

If the R71620 is connected to the indicator, through this step it is possible to enable the dedicated protocol, for the

serial ports set with the “

riPE 6

” protocol.

DISABLED

ENABLED

(!) DISABLED

<< Prn.FMt

PRINT CONFIGURATION

Through this step one can configure up to 30 print formats directly from the indicator.
In this step it is possible to choose the number of format to be configured; therefore enter, modify or eliminate the

print blocks following the instructions shown in section

7 PROGRAMMING THE PRINTOUTS

<< tErMin

SET TERMINATOR TYPE

When connecting a printer it is possible to define the end of the print line, in the print blocks provides the terminator

print (indiT, see 7.3 section)

TERMINATOR CR (character 13 from ASCII table)

Cr LF

TERMINATOR CR LF (character 13 and character 10 from ASCII table)

Содержание 3590 EBOX Series





































































































































Результаты поиска

Содержание 3590 EBOX Series

Отзывы:

Бренды по названию

Популярные бренды

Dini Argeo 3590 EBOX Series, Техническое руководство

Результаты поиска

Содержание 3590 EBOX Series

Отзывы:

Бренды по названию

Популярные бренды