Dini Argeo 3590 EBOX Series Скачать руководство пользователя страница 108

Страница: 108 / 132

3590EKR, 3590EXP, 3590EXT, 3590 EBOX, CPWE, CPWET series indicator E-AF03_05.01_14.07_EN_T.doc

108

439

JUST 1

OUTPUT WEIGHT

XXXXXXXX

in which XXXXXXXX is the value of the first stored output weight, including the comma.

440

JUST OUTPUT TRAILER WEIGHT

XXXXXXXX

in which XXXXXXXX is the value of the trailer output weight, including the comma.

NOTE:

the block is ignored if the trailer weight has not been enabled.

441

VEHICLE WEIGHT IN INPUT

IN WEIGH:

bbbbb

XXXX T

in which XXXXXXXX is the value of the stored input weight, including the comma.

442

TRAILER INPUT WEIGHT

TRAILER

bbbbb

XXXX T

in which XXXXXXXX is the value of the trailer input weight, including the comma.

NOTE:

the block is ignored if the trailer weight has not been enabled.

468

SCALE 1 WEIGHT FOR “A+B”

bbbb

XXXXXX T

The macro is printed if scale 1 or the sum of scales is displayed.

469

ONLY SCALE 1 WEIGHT FOR “A+B”

XXXXXXXXXX

470

SCALE 2 WEIGHT FOR “A+B”

bbbb

XXXXXX T

The macro is printed if scale 1 or the sum of scales is displayed.

471

ONLY SCALE 2 WEIGHT FOR “A+B”

XXXXXXXXXX

472

WEIGHT SUM FOR “A+B”

B1+B2

XXXXXX T

The macro is printed if the sum of the scales is displayed.

473

ONLY WEIGHT SUM FOR “A+B”

XXXXXXXXXX

476

PERCENT VALUE OF WEIGHT INCREMENT/DIMINUTION COMPARED WITH THE INITIAL WEIGHT

XXX.X

NOTA

: if the printing characters are not set with 617 macro or the values are incorrect (decimal number > characters

number), the percent value is always printing on 5 characters, including decimal point and one decimal number.

486

PRINTS CONDITIONED ADDITIONAL TARE

+PT

bbbbbbbbbbb

XXXX T

487

JUST ADDITIONAL TARE VALUE

XXXXXXXX

509

PRINT ONLY WEIGHT INPUT OR OUTPUT AT DEPENDING ON DIRECTION

XXXXXXXX

510

PRINT THE BIGGEST ONE WEIGHT

XXXXXXXX

between weigh in input – output (always gross)

511

PRINT THE SMALLEST ONE WEIGHT

XXXXXXXX

between weigh in input – output (always tare)

512

PRINT THE BIGGEST ONE WEIGHT

XXXXXXXX

between weigh in input – output for the second weight (always gross)

513

PRINT THE SMALLEST ONE WEIGHT BETWEEN

XXXXXXXX

between weigh in input – output for the second weight (always tare)

PARTIAL TOTAL

304

NET PARTIAL TOTAL

N.YYY

T1.N.XXXXXXXX

in which YYY shows the number of weighs, XXXXXXXX the weight value in 8 digits including the comma.

384

JUST WEIGHS PARTIAL TOTAL

XXXXXXXX

385

JUST NET PARTIAL TOTAL

XX…X

GENERAL TOTAL

305

NET GENERAL TOTAL

N.YYY

T2.N.

XXXXXXXX

UM + T

370

JUST GENERAL TOTAL WEIGHS

XXXXXXXX

the field expands from right to left with many spaces for completing the field length.

371

JUST NET GENERAL TOTAL

XX…X

GRAND TOTAL

306

NET GRAND TOTAL

N.YYY

T3.N.

XXXXXXXX

UM + T

386

JUST WEIGHS GRAND TOTAL

XXXXXXXX

387

JUST NET GRAND TOTAL

XX…X

Содержание 3590 EBOX Series





































































































































Результаты поиска

Содержание 3590 EBOX Series

Отзывы:

Бренды по названию

Популярные бренды

Dini Argeo 3590 EBOX Series, Техническое руководство

Результаты поиска

Содержание 3590 EBOX Series

Отзывы:

Бренды по названию

Популярные бренды