Digitax M1 mdt, Установка и программирование

Страница: 36 / 84

The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely con fi dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
36
31
Is extra charge n.4 a percentage or a cost? - Determines whether extra charge number 4 (the value of Q.27) is to be interpreted as a percentage
(Yes) or as a cost (No). The allowed answer is either 0 (No: Fixed-cost) or 1 (Yes: percentage of the fare).
0=cost
1=
percentage
32
Remember last used block num.? (next fare) - Should the last block number that has been used be remembered in order to be used again for
the next fare?
No / Yes
33
Enable discard current fare in Stopped? - This op on enables the possibility to discard the sta s cs of the current fare by pressing the keys K4
and OP, passing to ForHire. The allowed answer is either: No(enabled) or Yes (disabled).
No / Yes
34
Enable/disable measurements? - Should the distance measurement be disabled while in Stopped? The allowed answer is either: No(enabled)
or Yes (disabled).
No / Yes
35
Enable/disable measurements? - Should the wai ng- me measurement be enabled while in Stopped? The allowed answer is either:
No(enabled) or Yes (disabled).
No / Yes
36
Enable/disable measurements? - Should the distance measurement be disabled while in Hired? The allowed answer is either: No(enabled)
or Yes (disabled).
No / Yes
37
Enable/disable measurements? - Should the wai ng- me measurement be disabled while in Hired? The allowed answer is either: No(enabled)
or Yes (disabled).
No / Yes
NIGHT TIME (Prog - Date N. 1)
38
Start of night- me - This is the moment (whole or half hour) in which night- me starts. The me is given in whole hours with an accuracy of 1
hour. The allowed value goes from 0 (min) to 23 (max). It is also possible to specify half hours. In order to do this add 100 to the programmed
value. For example, to program the hour 22:30 use the value 122. 0 - 23
39
End of night- me - This is the moment (whole or half hour) in which night- me ends. The me is given in whole hours with an accuracy of 1
hour. The allowed value goes from 0 (min) to 23 (max). It is also possible to specify half hours. In order to do this add 100 to the programmed
value. For example, to program the hour 06:30 use the value 106. 0 - 23
40
Block-number in night- me - The block number (absolute) to be used during the hours considered night- me (Prog-Date 1) as programmed in
Q.38 and Q.39. The allowed value goes from 0 (min) to 62 (max).
0 - 62
41
Block-o
ff
set in night- me - The block o
ff
set (rela ve) to be used during the hours considered night- me (Prog-Date 1) as programmed in Q.38
and Q.39. The rela ve block o
ff
set is the number of blocks to add to the current block number in order to obtain the new block number. The
allowed value goes from 0 (min) to 62 (max).
0 - 62
42
Percentage or cost in night- me - This is the percentage or the cost that will be applied during night- me. The interpreta on as a percentage
or as a cost depends on ques ons Q.43 to Q.50. In case of percentage consider Q.43 to Q.46, Q.48 and Q.50. Ques ons Q.47 and Q.49 should
be answered with: NO. In case of cost consider Q.47 and Q.49. Ques ons Q.43 to Q.46, Q.48 and Q.50 should be answered with: NO. The cost
is given in the local currency with an accuracy of 1. The allowed value goes from 0 (min) to 65535 (max). See Q.273 and Q.274 for adding a
fi xed
decimal point. The percentage is given with an accuracy of 0.1. The allowed value goes from 0 (min) to 6553.5 (max).
0 - 65535
percentage/
cost
43 Increase unit-cost in night- me - Should the unit-cost (Q.8 to Q.10) in night- me be increased based on the percentage (Q.42)? No / Yes
44 Increase ini al-cost in night- me - Should the ini al-cost (Q.11) in night- me be increased based on the percentage (Q.42)? No / Yes
45 Decrease unit-distance in night- me - Should the unit-distance (Q.2 to Q.4) in night- me be decreased based on the percentage (Q.42)? No / Yes
46
Decrease unit-wai ng- me in night- me - Should the unit-wai ng- me (Q.5 to Q.7) in night- me be decreased based on the percentage
(Q.42)?
No / Yes
47
Insert as
fi
xed cost in night- me - Insert Q.42 at Stopped in N-T as Fixed Cost? When passing from Hired to Stopped in night- me should the
parameter of Q.42 be inserted as a
fi
xed cost ?
No / Yes
48
Insert as percentage in night- me - When passing from HIRED to STOPPED in night- me should the parameter of Q.42 be inserted as a
percentage?
No / Yes
49
Insert as fi xed cost in night- me with K1 - Passing from HIRED to STOPPED in night- me should the parameter of Q.42 be inserted as a fi xed
cost pressing key K1?
No / Yes
50
Insert as percentage in night- me with K1 - Passing from Hired to Stopped in night- me should the parameter of Q.42 be inserted as a
percentage pressing key K1?
No / Yes
H OLIDAY ( Prog-Date N. 2 )
51
Day of week considered holiday - This is the number that corresponds with the day of the week that is to be considered a holiday. The allowed
number goes from 0 (min) to 7 (max). The numbers have the following meaning:
0 - 7
0 ==> Disabled 1 ==> Monday 2 ==> Tuesday 3 ==> Wednesday
4 ==> Thursday 5 ==> Friday 6 ==> Saturday 7 ==> Sunday
52
Block-number in holiday- me - The block number (absolute) to be used during the days considered holiday- me (Prog-Date 2) as programmed
in Q.51. The allowed value goes from 0 (min) to 62 (max).
0 - 62
53
Block-o
ff
set in holiday- me - The block o
ff
set (rela ve) to be used during the week-days considered holiday- me (Prog-Date 2) as programmed
in Q.51. The rela ve block o
ff
set is the number of blocks to add to the current block number in order to obtain the new block number. The
allowed value goes from 0 (min) to 62 (max).
0 - 62
54
Percentage or cost in holiday- me - This is the percentage or the cost that will be applied during holiday- me. The interpreta on as a percentage
or as a cost depends on ques ons Q.55 to Q.62. In case of percentage consider Q.55 to Q.58, Q.60 and Q.62. Ques ons Q.59 and Q.61 should be
answered with: NO. In case of cost consider Q.59 and Q.61. Ques ons Q.55 to Q.58, Q.60 and Q.62 should be answered with: NO. The cost is
given in the local currency with an accuracy of 1. The allowed value goes from 0 (min) to 65535 (max). See Q.273 and Q.274 for adding a
fi
xed
decimal point. The percentage is given with an accuracy of 0.1. The allowed value goes from 0 (min) to 6553.5 (max).
0 - 65535
percentage/
cost
55 Increase unit-cost in holiday- me - Should the unit-cost (Q.8 to Q.10) in holiday- me be increased based on the percentage (Q.54)? No / Yes
56 Increase ini al-cost in holiday- me - Should the unit-cost (Q.11) in holiday- me be increased based on the percentage (Q.54)? No / Yes
57 Decrease unit-distance in holiday- me - Should the unit-distance (Q.2 to Q.4) in holiday- me be decreased based on the percentage (Q.54)? No / Yes
58
Decrease unit-wai ng- me in holiday- me - Should the unit-wai ng- me (Q.5 to Q.7) in holiday- me be decreased based on the percentage
(Q.54)?
No / Yes
59 Insert as
fi
xed cost in holiday- me - When passing from HIRED to STOPPED in holiday- me should the parameter of Q.54 be inserted as a
fi
xed cost? No / Yes