Digitax M1 mdt, Установка и программирование

Страница: 14 / 84

The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely con fi dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
14
“E-Seal”- Electronic Sealing:
1st Sec on: Last 100 Reading Changes Done
The “E-Seal” is a non-erasable memory spli ed in two sec ons where, in the
fi
rst sec on, are recorded the last 100
altera ons made on the programming func ons. These are shown on the displays or printed, with detailed informa-
on of: index nr, event, date, year and hour. The second sec on is made of permanent, non-rese able, progressive
individual events counter, incremented by each event altera ons without details. The
fi
rst sec on is by default a FIFO
bu
ff
er, with the last 100 events recorded, but can be con
fi
gured by tari
ff
to disable the FIFO and block the taximeter
when it reaches its maximum capacity. The second sec ons (counters) is never FIFO, and when reaches its maximum
capacity of 1000 events on any counter, the taximeter shows “ESEAL FULL” and it is blocked un l the mechanical seal
is broken and the taximeter is again ini alized
.
The “E-Seal” Reading, is included in the “SelfFun on Menu”. This is the procedure to enter it:
1) Keep pressed
K2 at least for two seconds to enter in the menu selec on
2) Select E-Seal menu by pressing K2 key
3) Com
fi
rm by K4 the E-Seal reading.
Now the
fi
rst Record is showed on the display (see
fi
gure 1). To increase the record index press K4 ; to decrease the
record index press K3 . The following pictures are only an example of E-Seal records because every single device could
have a di
ff
erent records sequence.
MAIN DISPLAY PRINTED REPORT DESCRIPTION EVENTS
K-Cons
K-CONS Constant “K” calibra on Autotest
A.DEFL
A.DEFL A er checksum error with black key inserted Autodefault
TARIFF
TARIFF Tari
ff
Programming Tari
ff
CLOCK
CLOCK Clock se ng Clock
SYN.CL
SYN.CL Clock +/- 2’ syncro Syncro Clock
TICKET
TICKET cket heading programming Header Ticket
M.E.S.
M.E.S. Mul extra-charge system programming Mes
CL.MEM
CL.MEM Sta s cal Memory block reset (block 2) Clear memo
DEFAUL
DEFAUL
By manual opera on General Default
LB.RES
LB.RES Long Bu
ff
er Memory Reset Long Bu
ff
er Reset
BIOS
BIOS Firmware changed Bios Change
LIGHTS
LIGHTS Taxi Roof Lights Test Light Test Result
4) By pressing K4 the E-Seal menu has two op ons depend-
ing on the event type. In that case showing Bios event type
by pressing
K4 we will see the Bios Checksum Programmed.
By pressing again K4 we will go to the next event type.
5) In that event type by pressing K4 we will go to the next
event type (
DEFAUL
).
6) By pressing K3 we will go to the previous event type
(
LB. RES
)
(
fi
gure 1)
7) Press
OP
to exit and return to main screen
Note:
At any index posi on by pressing K1 the E-Seal counters report will be printed
At any index posi on by pressing OP the taximeter will come back to
For Hire posi on
1) Modi
fi
ed Record Number
2) Event type
3) Event Modi
fi
ca on Date
4) Event Modi fi ca on Time
5) Event Value
BIOS 0
operator.ID event type
E-SEAL
BIOS 23241
event type
10.50
LB.RES 0
operator.ID event type
DEFAUL 0
operator.ID event type
LB.RES 0
operator.ID event type