Digitax M1 mdt, Установка и программирование

Страница: 43 / 84

The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely con fi dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
43
196
Block taxi-meter on disp.-segment-error? - At the end of the current fare should the taxi-meter be blocked in case of a display-segment-error?
The allowed answer is either: 0 (No: don’t block) or: 1 (Yes: block). No / Yes
197
Disable the display-dim func on?
- The possibility to dim the display should be disabled? General: the allowed answer is either: 0
(No: enable dimming) or: 1 (Yes: disable dimming). The intensity itself can be programmed with Q.198.
No / Yes
198
Intensity displ.-dim func on is 50% or 75%? - The intensity of the display can be programmed to have one of two values: 50% or 75%.
The allowed answer is either: 0 (No: 50%) or: 1 (Yes: 75%). The display-dim func on can be enabled by programming Q.197.
0=50%
1=75%
199
Fixed Cross-speed : the calcula on of the cost of a fare is either based on me or based on distance.
Below a certain velocity it is convenient to calculate the cost based on me (and not on distance). Above that velocity however it is convenient
to calculate the cost based on distance (and not on me). This velocity is the so called cross-speed. At this velocity the calculated cost is the
same for both me and distance. The velocity is given in Km/h with an accuracy of 1 Km/h. The allowed value goes from 0 (min) to 255 (max).
A
fi
xed cross-speed can be obtained by programming a value between 1 and 255 (Km/h). The value 0 is a special case (default). If 0 is
programmed then the cross-speed is calculated automa cally based on Q.2/3/4 and Q.5/6/7.
0 - 255
km/h
200
Alarm-velocity speedometer : this is the velocity above which an acous cal alarm-signal is produced.
If the (over-) velocity is maintained for at least 5 sec. Then it gets registered in the sta s cs. The registra on is maintained for the last 40 events.
So, at event n. 41 event n. 1 gets lost. The alarm-velocity is given in Km/h with an accuracy of 1 Km/h. The allowed value goes from 0 (min) to
255 (max). The value 0 is a special case (default). If 0 is programmed then the alarm speedometer is disabled.
0 - 255
km/h
201
Speedometer velocity-step : this is the step-amount (of velocity) with which the threshold of the speedometer gets decremented or incremented
every me key K3 (dec.) or key K4 (inc.) is pressed. The velocity-step is given in Km/h with an accuracy of 1 Km/h.
The allowed value goes from 0 (min) to 255 (max).
0-255
202
Enable manual setup of speedometer? - Should the possibility to setup the speedometer manually be enabled?
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
203 Show real- me speed on display? - Should the real- me speed of the car be shown on the secondary display? No / Yes
204 Show distance on display? - Should the (real- me) distance of the car be shown on the secondary display? No / Yes
205 Enable the Euro Conversion? No / Yes
206 Must the trip total amount be printed in Euro as well? No / Yes
207 During sums, extras inser on is not allowed? No / Yes
208 During sums, locks K4 (to avoid summing me to be extended) No / Yes
209 Disable the sum separa on with K4? No / Yes
210
Star ng-hour of dim-func on
: this is the moment (whole or half hour) star ng from which the display will be dimmed (according to Q.197 and
Q.198). The me is given in whole hours with an accuracy of 1 hour. The allowed value goes from 0 (min) to 23 (max). It is also possible to specify
half hours. In order to do this add 100 to the programmed value. For example, to program the hour 22:30 use the value 122. No / Yes
211
Ending-hour of dim-func on : this is the moment (whole or half hour) star ng from which the display will have normal intensity (according to
Q.197 and Q.198). The me is given in whole hours with an accuracy of 1 hour. The allowed value goes from 0 (min) to 23 (max).
It is also possible to specify half hours. In order to do this add 100 to the programmed value.
For example, to program the hour 22:30 use the value 122.
No / Yes
TAXI -LIGHT
212
Enable taxi-light ON in day- me? - Should it be possible for the taxi-light to be ON during the day- me?
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
213 The taxi-light must fl ash? - If Yes the taxi-light will fl ash. The allowed answer is either: 0 (No: no fl ash) or: 1 (Yes: fl ash). No / Yes
214
The taxi-light must go ON in overspeed? - If Yes then the taxi-light will go ON in case the actual velocity is higher than the velocity programmed
in Q.200. The allowed answer is either: 0 (No: OFF) or: 1 (Yes: ON).
No / Yes
215 Taxi-light must go on overspeed? No / Yes
from Q 216 / available for any possible so ware extension / to Q 218