The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely con
fi
dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
49
329
Inhibit prin ng memory-block n. 2?
- Should it be impossible to print memory-block number 2? See also Q.330.
The allowed answer is either: 0 (No: print) or: 1 (Yes: inhibit).
No / Yes
330
Enable prin ng MB2 with password ?
- If the prin ng of memory-block number 2 has been inhibited (see Q.329) should it be possible to
undo this with the password?
The allowed answer is either: 0 (No: keep inhibited) or: 1 (Yes: enable with password).
No / Yes
331
Inhibit reset of memory-block n. 2?
- Should it be impossible to reset memory-block number 2 from panel?
See also Q.332. The allowed answer is either:
0 (No: reset from panel) or: 1 (Yes: inhibit).
No / Yes
332
Enable reset of MB2 with password?
- If the reset from panel of memory-block number 2 has been inhibited (see Q.331) should it be possible
to undo this with the password?
The allowed answer is either: 0 (No: keep inhibited) or: 1 (Yes: enable with password).
No / Yes
333
Enable auto-advance of stat. memory?
- Should the number of the sta s cs-memory advance automa cally (instead of manually) during the
reading-procedure ?
The allowed answer is either: 0 (No: manually) or: 1 (Yes: automa cally).
No / Yes
334
Divide income of mem.-block n. 2 by 100?
- Should the income of memory-block n. 2 be divided by 100?
The allowed answer is either: 0 (No: don’t divide) or: 1 (Yes: divide).
No / Yes
PRE-PAID CARD
335
Hide on the Ticket the message “Thanks”?
No / Yes
336
Enable on the Ticket the 3 lines footer?
No / Yes
337
On service messages use normal font?
No / Yes
from Q 338 to Q 339
available for any possible so ware extension
FIXED COST FARE ( forfait)
340
Enable appl. of cost with num. keypad?
- Enable the applica on of a
fi
xed cost with the numeric keypad?
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
341
Enable programming forfait with front keys?
- If yes then, with the taximeter in Hired and pressing the keys K1 + K4 together, the forfait amount
can be programmed on the primary display. On the secondary display the text FORFA will be shown.
Programming:
pressing key K1 increases the amount with 1 unit
pressing key K2 increases the amount with 10 units;
pressing key K3 increases the amount with 100 units
pressing key K4 increases the amount with 1000
units;
pressing keys K3 + K4 cancels the modi
fi
ca ons made up to this point pressing key OP the forfait programming is exited.
Once exited from the forfait programming the amount shown on the display will not change anymore independently from the run distance or
the wai ng me un l the next me a new fare is started.
Note:
In order for this func on to work well it is necessary to program several ques ons
in block number 62 because this is the block that is loaded when the forfait is
used according to the following list:
No / Yes
Q13 = 0 : disable key K1
Q21 = 0 : no extra-charge n. 1
Q23 = 0 : no extra-charge n. 2
Q25 = 0 : no extra-charge n. 3
Q27 = 0 : no extra-charge n. 4
Q34 = Yes : disable distance measurement in
Stopped
Q36 = Yes : disable distance measurement in Hired
Q37 = Yes : disable wai ng- me measurement in Hired
Q40 = 0 : disable Night- me
Q41 = 0 : disable Night- me
Q52 = 0 : disable Holiday- me
Q53 = 0 : disable Holiday- me
The allowed answer is either:
0 (No: disabled) or: 1 (Yes: enabled).
Содержание M1 mdt
Страница 1: ...Technical Manual InstallationandProgramming ver 1 16 12 2014...
Страница 2: ......
Страница 83: ......
