Digital Equipment DECmpp 12000/Sx 100 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 156

background image

4.2 Auxiliary PCBs

Figure 4–1 DPU-Server Cables

Modem
PCB

Internal Phone Cable

Phone
Line

Internal VME
Data Cable

29-29565-01

DPU

Front-End

VME
Interface
PCB
(MVIB)

2T-T6000-AA

29-29373-01

Internal RS232 Cable

29-29566-01

DECsystem 5900

External RS232 Cable

External VME Data Cable

Internal Cables Used on -LC Configuration Only

MKV-040000314-40-DG

External RS232 Cable

29-29564-01

External VME
Data Cable

29-29563-01

DECstation 5000/240

4.2 Auxiliary PCBs

Auxiliary PCBs are defined as those not located in the DPU card cage. The
DECmpp 12000/Sx Series DPUs have three auxiliary PCBs mounted inside the
DPU enclosure.

•

DPU Interconnect PCB (DECmpp 12000-LC/Sx configuration only)

Provides a bulkhead connection for the VME and RS-232 cables. It is located
inside the DPU, at the lower rear, behind the power supply.

•

Lightpipe PCB

Drives the LEDs on the DPU front indicator panel. In DECmpp 12000
systems this is mounted to the inside of the front door, along with the power
switch assembly. In DECmpp 12000–LC systems it is mounted inside the
DPU top cover, over the inner front door.

•

Power Supply Controller PCB

Controls the power sequencing system. This PCB is located inside the power
tray enclosure.

4–2 Cables, Connectors, and Auxiliary PCBs

«
...
36
37
38
39
40
...
»

Содержание DECmpp 12000/Sx 100





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DECmpp 12000/Sx 100

NSLU2 - Network Storage Link NAS Server

Бренд: Linksys Страницы: 64

Бренд: AXIOMTEK Страницы: 55

Бренд: Artesyn Страницы: 190

Бренд: Olive Страницы: 44

Бренд: Goonas Страницы: 13

Бренд: Atop Страницы: 2

SUPERSERVER 1018D-73MTF

Бренд: Supero Страницы: 124

Бренд: Navico Страницы: 2

Бренд: Gigabyte Страницы: 120

Бренд: Opengear Страницы: 4

1870N - HL B/W Laser Printer

Бренд: Brother Страницы: 204

Бренд: 7th Sense Страницы: 60

Бренд: Thecus Страницы: 94

Бренд: DATONG Страницы: 23

Бренд: ClearCube Страницы: 5

Бренд: Planet Страницы: 2

Бренд: Inspur Страницы: 196

Бренд: Optibase Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды