Digital Equipment DECmpp 12000/Sx 100 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 156

background image

First Printing, January 1992
Revised, September 1992

The information in this document is subject to change without notice and should not be construed
as a commitment by Digital Equipment Corporation. Digital Equipment Corporation assumes no
responsibility for any errors that may appear in this document.

The software described in this document is furnished under a license and may be used or copied
only in accordance with the terms of such license.

NOTICE—Class A Computing Device:
This equipment generates, uses, and may emit radio frequency energy. The equipment has been
type tested and found to comply with the limits for a Class A computing device pursuant to Subpart
J or Part 15 of FCC rules, which are designed to provide reasonable protection against such radio
frequency interference when operated in a commercial environment. Operation of this equipment in
a residential area may cause interference; in which case, measures taken to correct the interference
are at the user’s expense.

Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions
as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software
clause at DFARS 252.227-7013.

© Digital Equipment Corporation 1992.

All Rights Reserved.

The postpaid Reader’s Comments forms at the end of this document request your critical evaluation
to assist in preparing future documentation.

The following are trademarks of Digital Equipment Corporation: DECnet, DECstation, DECsupport,
DECsystem, DECwindows, Rdb/VMS, ThinWire, TURBOchannel, ULTRIX, VAX, VAX DOCUMENT,
VMS, and the DIGITAL logo.

The following are registered trademarks of the MasPar Computer Corporation: MasPar and
the MasPar logo. The following are trademarks of the MasPar Computer Corporation: MasPar
Data Display Library (MPDDL), MasPar FORTRAN (MPF), MasPar Input/Output Channel,
MasPar Parallel Application Language (MPL), MasPar Parallel Disk Array (MPDA), and MasPar
Programming Environment (MPPE). UNIX is a registered trademark of UNIX System Laboratories,
Inc.

This document was prepared using VAX DOCUMENT, Version 2.0.

«
1
2
3
4
...
»

Содержание DECmpp 12000/Sx 100





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DECmpp 12000/Sx 100

BladeCenter PN41

Бренд: IBM Страницы: 88

Virtual Services Platform 7000 Series

Бренд: Avaya Страницы: 103

Бренд: IEI Technology Страницы: 89

System x3250 M3 Type 4251

Бренд: IBM Страницы: 32

Бренд: Altos Страницы: 93

WLNG-AN-DP500 Series

Бренд: Quatech Страницы: 120

Бренд: Kyocera Страницы: 207

301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard...

Бренд: LaCie Страницы: 74

Aironet 1500 Series

Бренд: Cisco Страницы: 8

7835-H2 - Media Convergence Server

Бренд: Cisco Страницы: 8

APP1000 - One Application Server Appliance

Бренд: Cisco Страницы: 20

Бренд: Cisco Страницы: 130

TS-73AeU Series

Бренд: QNAP Страницы: 70

Бренд: Avaya Страницы: 270

Бренд: Planet Страницы: 68

Бренд: Promise Technology Страницы: 2

cPCI-6510 Series

Бренд: ADLINK Technology Страницы: 112

SuperServer AS -2024US-TRT

Бренд: Supermicro Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды