Digital Equipment DECmpp 12000/Sx 100 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 156

background image

6.6 Replacing the DECmpp 12000–LC/Sx DPU Fan Tray

6.6 Replacing the DECmpp 12000–LC/Sx DPU Fan Tray

Take the following steps to replace the DECmpp 12000–LC/Sx DPU fan tray:

1.

Turn off the system power, as described in Chapter 1. Set the 15 A circuit
breaker to OFF (down), and unplug the power cord from the power source.

2.

Open the front and lower-front doors.

3.

Open the front inner door.

4.

Remove the front inner door:

•

Unplug the switch connector from the lightpipe (under the top cover).

•

Pull down on the latch on the upper hinge and pull the door out. Place
the door upright against the wall.

5.

Disconnect the power connector from the fan tray.

6.

Remove the four Phillips Screws that secure the fan tray to the frame. In
some cases, to be able to slide the fan tray out, you may need to remove the
+5 V cables from the power supply.

7.

Slide the fan tray out.

8.

Slide in the replacement fan tray. Reconnect the +5 V cables to the power
tray if they were removed.

9.

Replace the four Phillips Screws that secure the fan tray to the frame.

10. Connect the power connector to the fan tray.

11. Replace the front inner door:

•

While holding the upper hinge latch down, put the door in place, securing
the lower hinge and then sliding the upper hinge into place so that the
latch connects properly.

•

Reconnect the switch connector to the rightmost lightpipe connector.

12. Close and latch the front inner door.

13. Close and latch the front and lower-front doors.

14. Turn on the power to the DPU and make sure that the fan is working

properly.

Removal and Replacement Procedures 6–19

«
...
67
68
69
70
71
...
»

Содержание DECmpp 12000/Sx 100





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DECmpp 12000/Sx 100

Бренд: IBM Страницы: 64

RS/6000 7043 43P Series

Бренд: IBM Страницы: 322

System x3400 M3 Types 7378

Бренд: IBM Страницы: 45

QS21 - BladeCenter - 0792

Бренд: IBM Страницы: 110

Бренд: Sercomm Страницы: 75

Aspire EASYSTORE H341

Бренд: Acer Страницы: 59

Aspire EASYSTORE H341

Бренд: Acer Страницы: 74

Aspire EasyStore Series

Бренд: Acer Страницы: 148

Aspire easyStore H340

Бренд: Acer Страницы: 68

Altos EasyStore

Бренд: Acer Страницы: 169

Aspire easyStore H340

Бренд: Acer Страницы: 148

Altos EasyStore

Бренд: Acer Страницы: 7

PowerEdge 400SC

Бренд: Dell Страницы: 1

imagePRESS Server G200

Бренд: Canon Страницы: 98

imagePRESS A3200

Бренд: Canon Страницы: 192

ColorPass-Z7400

Бренд: Canon Страницы: 210

Бренд: Alcatel-Lucent Страницы: 4

Бренд: IBM Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды