Digital Equipment DECmpp 12000/Sx 100 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 156

background image

6.2 DPU Card Cage Slots

6.2 DPU Card Cage Slots

The DPU card cage is divided into two dedicated blocks: one for I/O PCBs and
the other for PE array PCBs, as shown in Figure 6–3. The DECmpp 12000
supports the ACU, the VME interface PCB, 16 PE array PCBs, and 15 I/O PCBs.
The DECmpp 12000–LC supports the ACU, the VME interface PCB, 4 PE array
PCBs, and 5 I/O PCBs.

6.2.1 I/O Slots

The first I/O slot, labeled ACU, always holds the ACU PCB. The second I/O slot

(slot IO00) is configured to support the Front-end VME interface PCB (MVIB).
This is a T6000 PCB mounted on a Parallel VME 6U Adapter PCB. The other
slots are for the PVME PCB and VMEbus PCBs mounted on Parallel VME 6U
Adapters.

In the DECmpp 12000 configuration, physical slot 10 (slot IO08) is reserved for
the PVME controller PCB and physical slot 6 (slot IO04) is reserved for the PDA
interface.

In the DECmpp 12000–LC configuration, physical slot 5 (slot I/O 03) is reserved
for the PVME controller and physical slot 6 (slot IO04) is reserved for the PDA
interface.

6.2.2 PE Array PCB Slots

DECmpp 12000 systems support 1, 2, 4, 8, or 16 PE array PCBs; DECmpp
12000–LC systems support 1, 2, or 4 PE array PCBs. The PE array PCBs must
be in contiguous slots, starting with the first PE array PCB slot. If the number of
PE array PCBs changes, backplane jumpers must be reconfigured, as described in
Chapter 7.

All PE array PCB slots that do not contain a PE array PCB must contain a router
PCB. The DECmpp will not work if any PE array PCB slot is empty.

6–4 Removal and Replacement Procedures

«
...
52
53
54
55
56
...
»

Содержание DECmpp 12000/Sx 100





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DECmpp 12000/Sx 100

eServer 380 xSeries

Бренд: IBM Страницы: 112

SUPERSERVER 5018D-FN8T

Бренд: Supermicro Страницы: 124

Бренд: SmartSight Страницы: 113

SUPERSERVER 6015C-NT

Бренд: Supermicro Страницы: 110

Бренд: AXIOMTEK Страницы: 76

SuperServer 6024H-82

Бренд: Supero Страницы: 122

Access Server 316

Бренд: Cabletron Systems Страницы: 70

G4-40G-010-384T

Бренд: Viavi Страницы: 12

Бренд: Viavi Страницы: 12

Бренд: Check Point Страницы: 53

Бренд: FreeNAS Страницы: 4

A+ SERVER 1022G-URF

Бренд: Supero Страницы: 95

Бренд: Russound Страницы: 44

QuickServer 1011

Бренд: FieldServer Страницы: 44

VxRail Appliance

Бренд: Dell EMC Страницы: 86

Бренд: Dell EMC Страницы: 131

PowerEdge R740xd

Бренд: Dell EMC Страницы: 215

Бренд: PaloAlto Networks Страницы: 240

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды