Digital Equipment DECmpp 12000/Sx 100 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 156

background image

4

Cables, Connectors, and Auxiliary PCBs

Chapter 4 describes and identifies the connectors and cables in the DECmpp
12000/Sx system. It also describes PCBs that are not mounted in the data
parallel unit (DPU) card cages.

4.1 Cables and Connectors

DECmpp 12000 systems require a 30 A, 250 V twist lock connector on a dedicated
circuit in the United States. Systems shipped outside the United States require
a 30 A, 220 Vac circuit and may be fitted with local cables and/or connectors
during installation. The DECmpp 12000/Sx Hardware Installation Guide lists
all optional power cable part numbers.

DECmpp 12000–LC systems must connect to either a dedicated 15 A, 110 Vac
circuit or to a dedicated 10 A, 220 Vac or 240 Vac circuit, depending on local
power availability.

Following are brief descriptions of cables and connectors for the front-end server
and the DPU. Refer to Figure 4–1 for a simplified diagram of the DECmpp
system internal and external cable connections. The internal cables are used on
the DECmpp 12000–LC configuration only.

•

Telephone Connection — Internal DPU 2-foot cable to the modem; external
cable length determined by installation site requirements (United States
only).

•

Data Cables

Internal 4 foot cable with 100-pin connectors between the Front-end VME
interface PCB (T6000) in the DPU card cage and the DPU rear panel
interconnect PCB.

External 15 foot cable with 100-pin connectors between the DPU rear panel
cable connection and the server rear panel connection.

•

Internal RS-232 Cable — Between the modem and the DPU rear panel
interconnect PCB.

•

External RS-232 Cable — Between the server rear panel and the DPU rear
panel cable connection.

•

Power Cable — In DECmpp 12000 systems, the power cable is wired directly
to a terminal block inside the DPU power supply. DECmpp 12000–LC
systems use a standard power cable.

Cables, Connectors, and Auxiliary PCBs 4–1

«
...
35
36
37
38
39
...
»

Содержание DECmpp 12000/Sx 100





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для DECmpp 12000/Sx 100

Бренд: G-Technology Страницы: 35

Link Manager 4010-43

Бренд: Point Six Страницы: 131

eServer 342 xSeries

Бренд: IBM Страницы: 70

Бренд: Hi-flying Страницы: 29

xPico XPW100A003-01-B

Бренд: Lantronix Страницы: 54

Transport TN27 B4987

Бренд: TYAN Страницы: 135

Бренд: Sun Oracle Страницы: 222

Бренд: DNP Страницы: 93

UniServer R2700 G3

Бренд: H3C Страницы: 226

S7000FC4UR - Server System - 0 MB RAM

Бренд: Intel Страницы: 13

x3105 - System - 4347

Бренд: IBM Страницы: 130

System x3650 Type 7979

Бренд: IBM Страницы: 194

Бренд: EXAGATE Страницы: 8

Бренд: 3onedata Страницы: 24

EMC VxFlex Appliance R840

Бренд: Dell Страницы: 44

EqualLogic PS4000

Бренд: Dell Страницы: 73

EMC PowerProtect DD6400 System

Бренд: Dell Страницы: 46

EqualLogic PS5500

Бренд: Dell Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды