Danfoss VLT AutomationDrive FC 300 Series, Руководство по программированию, Страница: 78 / 211

[6] Running / no
warning Output speed is higher than the speed
set in
1-81 Min Speed for Function at Stop
[RPM] . The motor is running and there
are no warnings.
[7] Run in range /
no warning Motor is running within the programmed
current and speed ranges set in
4-50 Warning Current Low to 4-53 Warning
Speed High . There are no warnings.
[8] Run on
reference / no
warning Motor runs at reference speed. No
warnings.
[9] Alarm An alarm activates the output. There are
no warnings.
[10] Alarm or
warning An alarm or a warning activates the
output.
[11] At torque limit The torque limit set in 4-16 Torque Limit
Motor Mode or 4-17 Torque Limit
Generator Mode has been exceeded.
[12] Out of current
range The motor current is outside the range
set in
4-18 Current Limit .
[13] Below current,
low Motor current is lower than set in
4-50 Warning Current Low .
[14] Above current,
high Motor current is higher than set in
4-51 Warning Current High .
[15] Out of range Output frequency is outside the
frequency range set in
4-52 Warning
Speed Low and 4-53 Warning Speed High .
[16] Below speed,
low Output speed is lower than the setting in
4-52 Warning Speed Low .
[17] Above speed,
high Output speed is higher than the setting
in
4-53 Warning Speed High .
[18] Out of
feedback range
Feedback is outside the range set in
4-56 Warning Feedback Low
and
4-57 Warning Feedback High .
[19] Below feedback
low Feedback is below the limit set in
4-56 Warning Feedback Low .
[20] Above
feedback high Feedback is above the limit set in
4-57 Warning Feedback High .
[21] Thermal
warning The thermal warning turns on when the
temperature exceeds the limit in the
motor, the frequency converter, the brake
resistor, or the thermistor.
[22] Ready, no
thermal
warning Frequency converter is ready for
operation and there is no over-
temperature warning.
[23] Remote, ready,
no thermal
warning Frequency converter is ready for
operation and is in [Auto On] mode.
There is no over-temperature warning.
[24] Ready, no
over-/ under
voltage Frequency converter is ready for
operation and the mains voltage is within
the specified voltage range (see
General
Specifications section in the Design
Guide).
[25] Reverse Reversing. Logic ‘1’ when CW rotation of
the motor. Logic ‘0’ when CCW rotation
of the motor. If the motor is not rotating
the output will follow the reference.
[26] Bus OK Active communication (no time-out) via
the serial communication port.
[27] Torque limit
and stop Use in performing a coasting stop and in
torque limit condition. If the frequency
converter has received a stop signal and
is at the torque limit, the signal is Logic
‘0’.
[28] Brake, no brake
warning Brake is active and there are no warnings.
[29] Brake ready, no
fault Brake is ready for operation and there are
no faults.
[30] Brake fault
(IGBT) Output is Logic ‘1’ when the brake IGBT is
short-circuited. Use this function to
protect the frequency converter if there is
a fault on the brake modules. Use the
output/relay to cut out the main voltage
from the frequency converter.
[31] Relay 123 Relay is activated when Control Word [0]
is selected in parameter group 8-**.
[32] Mechanical
brake control Enables control of an external mechanical
brake, see description in the section
Control of Mechanical Brake , and
parameter group 2-2*
[33] Safe stop
activated (FC
302 only) Indicates that the safe stop on terminal
37 has been activated.
[40] Out of ref
range Active when the actual speed is outside
settings in
4-52 Warning Speed Low to
4-55 Warning Reference High .
[41] Below
reference low Active when actual speed is below speed
reference setting.
[42] Above
reference high Active when actual speed is above speed
reference setting
[43] Extended PID
Limit
[45] Bus Ctrl Controls output via bus. The state of the
output is set in
5-90 Digital & Relay Bus
Control . The output state is retained in
the event of bus time-out.
[46] Bus Ctrl On at
timeout Controls output via bus. The state of the
output is set in
5-90 Digital & Relay Bus
Control . In the event of bus time-out the
output state is set high (On).
[47] Bus Ctrl Off at
timeout Controls output via bus. The state of the
output is set in
5-90 Digital & Relay Bus
Control . In the event of bus time-out the
output state is set low (Off).
[51] MCO controlled Active when a MCO 302 or MCO 305 is
connected. The output is controlled from
option.
[55] Pulse output
[60] Comparator 0 See parameter group 13-1*. If Comparator
0 is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
Parameter Descriptions
VLT
®
AutomationDrive Programmming Guide
MG33ME02 - VLT
®
is a registered Danfoss trademark 77
3 3