Danfoss VLT 2800 Series Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 120

Danfoss VLT 2800 Series Скачать руководство пользователя страница 98

Warnings/alarm messages

A warning or an alarm will appear in the display as a
numerical code

Err. xx

. A warning will be shown on

the display until the fault has been corrected, while an
alarm will continue to flash until the [STOP/RESET]
key is activated.The table shows the various warnings
and alarms, and whether the fault locks the adjustable
frequency drive. After a

Trip-locked

the line supply is

cut off and the fault is corrected. The line supply is re-
connected and the adjustable frequency drive is reset.
The adjustable frequency drive is now ready. A

Trip

can be reset manually in three ways:

1.

Via the operating key [STOP/RESET].

2.

Via a digital input.

3.

Via serial communication.

It is also possible to choose an automatic reset in pa-
rameter 405

Reset function

. When a cross appears in

both warning and alarm, this can mean that a warning
comes before an alarm. It can also mean that it is pos-
sible for the user to program whether a warning or an
alarm will appear for a given fault. For example, this is

possible in parameter 128

Motor thermal protection

.

After a trip, the motor will coast, and alarm and warning
will blink on the adjustable frequency drive; but if the
fault disappears, only the alarm will blink. After a reset,
the adjustable frequency drive will be ready to start
operation again.

No

Description

Warning

Alarm

Trip

locked

2

Live zero error (LIVE ZERO ERROR)

X

X

X

4

Line phase loss (LINE PHASE LOSS)

X

X

X

5

Voltage warning high (DC LINK VOLTAGE HIGH)

X

6

Voltage warning low (DC LINK VOLTAGE LOW)

X

7

Overvoltage (DC LINK OVERVOLT)

X

X

X

8

Undervoltage (DC LINK UNDERVOLT)

X

X

X

9

Inverter overload (INVERTER TIME)

X

X

10

Motor overloaded (MOTOR, TIME)

X

X

11

Motor thermistor (MOTOR THERMISTOR)

X

X

12

Current limit (CURRENT LIMIT)

X

X

13

Overcurrent (OVERCURRENT)

X

X

X

14

Ground fault (GROUND FAULT)

X

X

15

Switch mode fault (SWITCH MODE FAULT)

X

X

16

Short-circuit (CURR. SHORT CIRCUIT)

X

X

17

Serial communication timeout (STD BUS TIMEOUT)

X

X

18

HPFB bus timeout (HPFB TIMEOUT)

X

X

33

Out of frequency range (OUT FREQ RNG/ROT LIM)

X

34

HPFB communication fault (PROFIBUS OPT. FAULT)

X

X

35

Soft-charge fault (SOFT-CHARGE FAULT)

X

X

36

Overtemperature (OVERTEMPERATURE)

X

X

37-45

Internal fault (INTERNAL FAULT)

X

X

50

AMT not possible

X

51

AMT fault re. nameplate data (AMT TYPE.DATA FAULT)

X

54

AMT wrong motor (AMT WRONG MOTOR)

X

55

AMT timeout (AMT TIMEOUT)

X

56

AMT warning during AMT (AMT WARN. DURING AMT)

X

99

Locked (LOCKED)

X

LED indication

Warning

yellow

Alarm

red

Trip-locked

yellow and red

WARNING/ALARM 2: Live zero fault

The voltage or current signal on terminal 53 or 60 is
below 50% of the preset value in parameter 309 or 315

Terminal, min. scaling

.

VLT

®

2800 Series

98

MG.27.A2.22 - VLT

®

is a registered Danfoss trademark

«
...
96
97
98
99
100
...
»

Содержание VLT 2800 Series

























































































































Отзывы:

Нет отзывов