Danfoss VLT 2800 Series Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 120

Danfoss VLT 2800 Series Скачать руководство пользователя страница 58

227

Warning: Low feedback, FB

LOW

(warn.feedb. low)

Value:

-100,000.000 - par. 228

Warn.:

FB

HIGH

-4000.000

Function:

If the feedback signal falls below the preset limit
FB

LOW

, a warning is given.

Parameters 223-228

Warning functions

are out of

function during ramp-up after a start command and af-
ter a stop command or during stop. The warning func-
tions are activated when the output frequency has
reached the resulting reference.The signal outputs
can be programmed to give a warning signal via ter-
minal 46 and via the relay output.The unit for feedback
in Closed loop is programmed in parameter 416

Proc-

ess units

.

Description of choice:

Set the required value within the feedback range (pa-
rameter 414

Minimum feedback, FB

MIN

and 415

Max-

imum feedback, FB

MAX

).

228

Warning: High feedback, FB

HIGH

(warn.feedb high)

Value:

Par. 227

Warn.: FB

LOW

- 100,000.000

4000.000

Function:

If the feedback signal gets above the preset limit
FB

HIGH

, a warning is given.

Parameters 223-228

Warning functions

are out of

function during ramp-up after a start command and af-
ter a stop command or during stop. The warning func-
tions are activated when the output frequency has
reached the resulting reference. The signal outputs
can be programmed to give a warning signal via ter-
minal 46 and via the relay output. The unit for feedback
in Closed loop is programmed in parameter 416

Proc-

ess units

.

Description of choice:

Set the required value within the feedback range (pa-
rameter 414

Minimum feedback, FB

MIN

and 415

Max-

imum feedback, FB

MAX

).

229

Frequency bypass, bandwidth

(FREQ BYPASS B.W.)

Value:

0 (OFF) - 100 Hz

0 Hz

Function:

Some systems call for some output frequencies to be
avoided because of mechanical resonance problems

in the system. In parameters 230-231

Frequency by-

pass,

these output frequencies can be programmed.

In this parameter, a bandwidth can be defined on either
side of these frequencies.

Description of choice:

The frequency set in this parameter will be centered

around parameters 230

Frequency bypass 1

and 231

Frequency bypass 2

.

230

Frequency bypass 1 (FREQ. BYPASS 1)

231

Frequency bypass 2 (FREQ. BYPASS 2)

Value:

0 - 1000 Hz

0.0 Hz

Function:

Some systems call for some output frequencies to be
avoided because of mechanical resonance problems
in the system.

Description of choice:

Enter the frequencies to be avoided. See also param-
eter 229

Frequency bypass, bandwidth

.

VLT

®

2800 Series

= factory setting, () = display text, [] = value for use in communication via serial communication port

58

MG.27.A2.22 - VLT

®

is a registered Danfoss trademark

«
...
56
57
58
59
60
...
»

Содержание VLT 2800 Series

























































































































Отзывы:

Нет отзывов