Danfoss VLT 2800 Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 120

Danfoss VLT 2800 Series Скачать руководство пользователя страница 34

004

Active Setup

(active Setup)

Value:

Factory Setup (FACTORY SETUP)

[0]

setup 1 (setup 1)

[1]

setup 2 (setup 2)

[2]

Setup 3 (setup 3)

[3]

setup 4 (setup 4)

[4]

Multi Setup (MULTI SETUP)

[5]

Function:

The active parameter Setup is selected here. All pa-
rameters can be programmed in four individual pa-
rameter Setups. Shifts between Setups can be made
in this parameter via a digital input or via serial com-
munication.

Description of choice:

Factory Setup

[0] contains the factory-set parameter

values.

Setup 1-4

[1]-[4] are four individual Setups

which can be selected as required.

Multi Setup

[5] is

used where remote-controlled shifts between the four
Setups via a digital input or via serial communication
is required.

005

Programming Set-up

(EDIT SET-UP)

Value:

Factory Set-up (FACTORY SET-UP)

[0]

Set-up 1 (set-up 1)

[1]

Set-up 2 (set-up 2)

[2]

Set-up 3 (set-up 3)

[3]

Set-up 4 (set-up 4)

[4]

Active Set-up (ACTIVE SET-UP)

[5]

Function:

You can select the desired set-up to program during
operation (this applies both via the control panel and
the serial communication port). For example, it is pos-
sible to program

Set-up 2

[2] while the active set-up is

set to

Set-up 1

[1] in parameter 004

Active Set-up

.

Description of choice:

Factory Set-up

[0] contains the factory-set data and

can be used as a source of data if the other set-ups
are to be reset to a known status.

Set-up 1-4

[1]-[4]

consists of individual set-ups that can be programmed
freely during operation. If

Active Set-up

[5] is selected,

the programming set-up will be equal to parameter 004

Active Set-up

.

NOTE

If data is modified or copied to the active
set-up, the modifications have an imme-
diate effect on the unit's operation.

006

Setup copying

(SETUP COPY)

Value:

No copying (NO COPY)

[0]

Copy to Setup 1 from #
(COPY TO SETUP 1)

[1]

Copy to Setup 2 from #
(COPY TO SETUP 2)

[2]

Copy to Setup 3 from #
(COPY TO SETUP 3)

[3]

Copy to Setup 4 from #
(COPY TO SETUP 4)

[4]

Copy to all Setups from # (copy to all)

[5]

Function:

You can copy from the selected active Setup in pa-
rameter 005

Programming setup

to the selected Setup

or Setups in this parameter.

NOTE

Copying is only possible in Stop (motor
stopped in connection with a stop com-
mand).

Description of choice:

Copying begins when the required copying function
has been selected and the [OK]/[CHANGE DATA] key
has been pushed. The display indicates when copying
is in progress.

VLT

®

2800 Series

= factory setting, () = display text, [] = value for use in communication via serial communication port

34

MG.27.A2.22 - VLT

®

is a registered Danfoss trademark

«
...
32
33
34
35
36
...
»

Содержание VLT 2800 Series

























































































































Отзывы:

Нет отзывов