Danfoss VLT 2800 Series Скачать руководство пользователя страница 81

Страница: 81 / 120

464

Wakeup Pressure

(Wakeup Pressure)

Value:

Par. 204 Ref

MIN

– par. 215 - 218 Setpoint

Function:

When in Sleep mode the adjustable frequency drive
will wake up when the pressure is below the Wakeup
pressure for the time set in parameter 462

Enhanced

sleep mode timer

Description of choice:

Set an appropriate value for the system. The unit is set
in parameter 416.

465

Minimum pump frequency

(Pump min. freq.)

Value:

Value par. 201 f

MIN

– par. 202 f

MAX

(Hz)

Function:

This parameter is linked to parameter 467

Minimum

Power

and is used for no/low-flow power curve.

Description of choice:

Enter a value equal or close to the desired minimum

frequency set in parameter 201

Output frequency low

limit, f

MIN

. Please note that the extension of the no/low-

flow power curve is limited by parameters 201 and 202,
and not by parameters 465 and 466.

466

Maximum Pump Frequency

(Pump max. freq)

Value:

Value par. 201 f

MIN

- par. 202 f

MAX

(Hz)

Function:

This parameter is linked to parameter 468

Maximum

pump power

and is used for the no/low-flow power

curve.

Description of choice:

Enter a value equal or close to the desired maximum
frequency set in parameter 202

Output frequency high

limit, f

MAX

467

Minimum Pump Power

(Min. pump power)

Value:

0–500.000 W

Function:

The associated power consumption at the frequency

entered in parameter 465

Minimum pump frequency

Description of choice:

Enter the no/low-flow power reading at minimum pump
frequency entered in parameter 465.

Depending on pump size or curve, select W or kW in
par. 009 index [32] and [8] for fine tuning.

468

Maximum Pump Power

(Max. pump power)

Value:

0–500.000 W

Function:

The associated power consumption at the frequency
entered in parameter 466

Minimum pump frequency

Description of choice:

Enter the no/low-flow power reading at maximum
pump frequency entered in parameter 466.

Depending on pump size or curve, select W or kW in
par. 009 index [32] and [8] for fine tuning.

469

No Flow Power Compensation

(NF power comp)

Value:

0.01 - 2

1.2

Function:

This function is used for an off-set of the no/low-flow
power curve, which can be used as a safety factor or
for fine tuning the system.

Description of choice:

Description The factor is multiplied to the power val-
ues. E.g., 1.2 will increase the power value with 1.2
over the whole frequency range.

VLT

2800 Series

= factory setting, () = display text, [] = value for use in communication via serial communication port

MG.27.A2.22 - VLT

is a registered Danfoss trademark

Prog

rammi

Содержание VLT 2800 Series

























































































































Результаты поиска

Содержание VLT 2800 Series

Отзывы:

Danfoss VLT 2800 Series, Общее руководство пользователя, Страница: 81 / 120

Результаты поиска

Содержание VLT 2800 Series

Отзывы: