Danfoss VLT 2800 Series Скачать руководство пользователя страница 32

Страница: 32 / 120

safety interlock circuit to avoid un-
wanted drive trips.

•

No power factor correction capaci-
tors can be connected between
drive and motor.

•

Two speed motors must be wired
permanently for full speed.

•

Y-start,

-run motors must be wired

permanently for run.

Installation checks

Input fusing in power supply for all drives
must be provided.

Environmental concerns - for standard
NEMA 1 drive:

•

Clean air supply

•

Dry air (5% to 85% relative humidity,
non-condensing)

•

32°F (0°C) to 104°F (40°C) ambient
temperature operating range, or as
rated

•

1000m (3,300 ft) maximum eleva-
tion with no derating

•

Keep any construction dirt out of
drive.

Wiring

•

Wire drive in accordance with in-
structions and diagrams received
with drive.

•

Separate conduits must be provi-
ded to drive for input power, output
power, and control wiring.

•

Protect signal wires from noise.

•

Ground each drive individually.

•

Double check input and output pow-
er wiring for correct location.

Setting up drive for motor start

Ensure that all warnings provided in this manual have
been adhered to. Apply power to the unit. Enter motor
nameplate data into drive through Quick Menu.

Parameter 102, MOTOR POWER (in kW)
(See conversion table in parameter 102,

Mo-

tor Power,

in this manual.)

Parameter 103, MOTOR VOLTAGE

Parameter 104, MOTOR FREQUENCY

Parameter 105, MOTOR CURRENT

Parameter 106, MOTOR SPEED

Parameter 107, select AUTOMATIC MOTOR
TUNING

Operational tests - HAND

Check motor rotation from drive. If incorrect,
disconnect input power from drive and re-
verse two leads between drive and motor.

Accelerate motor quickly to full speed and
verify operation.

Decelerate motor quickly to stop and verify
operation.

Operate motor over entire speed range while
closely checking for resonance.

Operational tests - AUTO

Ensure that drive follows run/stop and safety
interlock commands from system.

Ensure drive follows speed reference, or
feedback, from system.

VLT

2800 Series

MG.27.A2.22 - VLT

is a registered Danfoss trademark

Содержание VLT 2800 Series

























































































































Результаты поиска

Содержание VLT 2800 Series

Отзывы:

Danfoss VLT 2800 Series, Общее руководство пользователя, Страница: 32 / 120

Результаты поиска

Содержание VLT 2800 Series

Отзывы: