Danfoss VLT 2800 Series Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 120

Danfoss VLT 2800 Series Скачать руководство пользователя страница 44

Description of choice:

R

S

can be set as follows:

1.

Use the factory settings of R

S

which the ad-

justable frequency drive itself chooses on the
basis of the motor nameplate data.

2.

The value is stated by the motor supplier.

3.

The value is obtained through manual meas-
urements: R

S

can be calculated by measur-

ing the resistance R

PHASE-PHASE

between two

phase terminals. Where R

PHASE-PHASE

is low-

er than 1-2 Ohms (typical for motors > 7.5
HP, 400 V), a special Ohm-meter should be
used (Thomson-bridge or similar).

R

S

= 0.5 x

R

PHASE-PHASE

.

4.

R

S

is set automatically when AMT has been

completed. See parameter 107

Auto motor

tuning.

109

Stator reactance X

S

(STATOR REACTANCE)

Value:

0.00 - X,XX

Ω

Depends on choice of motor

Function:

After parameters 102-106

Nameplate data

are set, a

number of parameters are adjusted automatically, in-
cluding stator reactance X

S

. The shaft performance

can be improved by fine-tuning R

S

and X

S

; see proce-

dure below.

Description of choice:

X

S

can be set as follows:

1.

The value is stated by the motor supplier.

2.

The value is obtained through manual meas-
urements; X

S

is obtained by connecting a

motor to line power and measuring the
phase-phase voltage U

M

and the idle current

φ

.

X

s

=

U

M

3 ×

I

ϕ

−

X

L

2

X

L

: See parameter 142.

3.

Use the factory settings of X

S

, which the ad-

justable frequency drive itself chooses on the
basis of the motor nameplate data.

117

Resonance damping

(resonance damping)

Value:

OFF 100

[OFF 100]

Off

[OFF]

Function:

It is possible to optimize the resonance damping in CT
mode. The grade of the influence is adjusted in this
parameter.
The value may be set between 0% (OFF) and 100%.
100% corresponds to 50% reduction of U/F ratio.
Default value is OFF.

Internal settings (fixed):
The resonance filter is active from 10% of nominal
speed and above.
In this case 5Hz and above.
Speed to go from 0 to nominal flux level: 500ms
Speed to go from nominal to 0 flux level: 500 ms

Description of functionality:
The filter monitors the active motor current and
changes the motor voltage according to the figure be-
low. The filter reacts on levels referring to the nominal
motor current.

If the active motor current is below 10%, the motor
voltage will be decreased by the speed mentioned
above until the voltage reaches the setting for Par.
117. If the active motor current comes over 20% the
voltage will be increased by the above-mentioned
speed. If the active motor current reaches 40% the
motor voltage will be increased immediately to normal
motor voltage.
The reduction in motor voltage depends on the pa-
rameter 117 setting.

VLT

®

2800 Series

= factory setting, () = display text, [] = value for use in communication via serial communication port

44

MG.27.A2.22 - VLT

®

is a registered Danfoss trademark

«
...
42
43
44
45
46
...
»

Содержание VLT 2800 Series

























































































































Отзывы:

Нет отзывов