Danfoss VLT 2800 Series Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 120

Danfoss VLT 2800 Series Скачать руководство пользователя страница 26

Control unit

On the front of the variable frequency drive there is a
control panel.

The control panel is divided into five functional groups:

1.

Status LED

2.

Keys for changing parameters and shifting
display function.

3.

LEDs.

4.

Keys for local operation.

All displays of data are in the form of a six-digit LED
display capable of showing one item of operating data
continuously during normal operation. As a supple-
ment to the display, there are three LEDs for indication
of electrical connection (ON), warning (WARNING)
and alarm (ALARM). Most of the variable frequency
drive's parameter Setups can be changed immediately
via the control panel, unless this function has been

programmed as

Locked

[1] via parameter 018

Lock for

data changes

.

Control keys

[QUICK MENU]

allows access to the parameters used

for the Quick menu.
The[QUICK MENU] key is also used if a change to a
parameter value is not to be implemented.
See also [QUICK MENU] + [+].

[CHANGE DATA]

is used for changing a setting.

The [CHANGE DATA] key is also used for confirming
a change of parameter settings.

[+] / [-]

are used for selecting parameters and for

changing parameter values.
These keys are also used in Display mode for selecting
the display of an operating value.

The

[QUICK MENU] + [+]

keys must be pressed at the

same time to give access to all parameters. See

Menu

mode.

[STOP/RESET]

is used for stopping the connected

motor or for resetting the variable frequency drive after
a trip.
Can be selected as

Active

[1] or

Not active

[0] via pa-

rameter 014

Local stop/reset

. In Display mode, the

display will flash if the stop function is activated.

NOTE

If the [STOP/RESET] key is set at

Not ac-

tive

[0] in parameter 014

Local stop/re-

set,

and there is no stop command via the

digital inputs or serial communication, the
motor can only be stopped by disconnect-
ing the electrical voltage to the variable
frequency drive.

[START]

is used for starting the variable frequency

drive. It is always active, but the [START] key cannot
override a stop command.

Manual initialization

To manually initialize the adjustable frequency drive to
factory default settings, first disconnect AC line volt-
age. Hold the [QUICK MENU] and [+] and [CHANGE
DATA] keys down while simultaneously reconnecting
the AC line voltage. Release the keys. The drive has
now been programmed for factory settings.

VLT

®

2800 Series

26

MG.27.A2.22 - VLT

®

is a registered Danfoss trademark

«
...
24
25
26
27
28
...
»

Содержание VLT 2800 Series

























































































































Отзывы:

Нет отзывов