Danfoss VLT 2800 Series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 120

Danfoss VLT 2800 Series Скачать руководство пользователя страница 23

No.

Function

01-03

Relay outputs 01-03 can be used for
indicating status and alarms/warnings.

12

24 V DC voltage supply.

18-33

Digital inputs.

20, 55

Common frame for input
and output terminals.

42

Analog output for displaying frequency,
reference, current or torque.

46

1

Digital output for displaying status,
warnings or alarms, as well as
frequency output.

50

+10 V DC supply
voltage for potentiometer or thermistor.

53

Analogue voltage input 0-10 V DC.

60

Analogue current input 0/4 - 20 mA.

67

1

+ 5 V DC supply voltage
to Profibus.

68, 69

1

RS-485, Serial communication.

70

1

Frame for terminals 67, 68 and 69.
Normally, this terminal is not to be used.

1. The terminals are not valid for DeviceNet/CANopen.
See also the DeviceNet manual, MG.90.BX.YY for fur-
ther details.

Relay connection

See parameter 323

Relay output

for programming of

relay output.

Nr.

01 - 02

1 - 2 make (normally open)

01 - 03 1 - 3 break (normally closed)

NOTE

Please note that the cable jacket for the
relay must cover the first row of control
card terminals - otherwise the galvanic
isolation (PELV) cannot be maintained.
Max. cable diameter: 4 mm. See drawing.

Profibus DIP switches setting

The dip switch is only on the control card with Profibus
DP communication. The switch position shown is the
factory setting. Switches 1 and 2 are used as cable
termination for the RS-485 interface. If the adjustable
frequency drive is located as the first or last (or only)
unit in the bus system, switches 1 and 2 must be ON.
On the remaining adjustable frequency drives,
switches 1 and 2 must be OFF. Switches 3 and 4 are
not applied.

VLT Software Dialog

Connection to terminals 68-70 or
Sub D:

-

PIN 3 GND

-

PIN 8 P-RS 485

-

PIN 9 N-RS 485

Sub D plug

An LCP 2 control unit can be connected to the Sub D
plug on the control card. Ordering number: 175N0131.
The LCP control unit with ordering number 175Z0401
is not to be connected.

VLT

®

2800 Series

MG.27.A2.22 - VLT

®

is a registered Danfoss trademark

23

In

s

tall

a

tio

n

«
...
21
22
23
24
25
...
»

Содержание VLT 2800 Series

























































































































Отзывы:

Нет отзывов