manualshive.com logo in svg

Danfoss VLT 2800 Series, Общее руководство пользователя, Страница: 108 / 120

Поделиться
Скачать
Danfoss VLT 2800 Series Скачать руководство пользователя страница 108

Cable lengths and cross-sections:

Max. motor cable length, shielded/armored cable

131 ft [40 m]

Max. motor cable length, unshielded/unarmored cable

246 ft [75 m]

Max. motor cable length, shielded/armored cable and motor coil

328 ft [100 m]

Max. motor cable length, unshielded/unarmored cable and motor coil

656 ft [200 m]

Max. motor cable length, shielded/armored cable and RFI/1B filter

200 V, 328 ft [100 m]

Max. motor cable length, shielded/armored cable and RFI/1B filter

400 V, 82 ft [25 m]

Max. motor cable length, shielded/armored cable and RFI 1B/LC filter

400 V, 82 ft [25 m]

Max. cross-section to motor, see next section.

Max. cross-section to control wires, rigid wire

0.0023 in.

2

 [1.5 mm

2

]/16 AWG (2 x 0.0012 in.

2

 [2 x 0.75 mm

2

])

Max. cross section to control cables, flexible cable

0.0016 in.

2

 [1 mm

2

]/18 AWG

Max. cross-section to control cables, cable with enclosed core

0.00078 in.

2

 [0.5 mm

2

]/20 AWG

When complying with EN 55011 1A and EN 55011 1B, the motor cable must be reduced in certain instan-
ces. See EMC emission.

Control characteristics:

Frequency range

0.2 - 132 Hz, 1 - 1000 Hz

Resolution of output frequency

0.013 Hz, 0.2 - 1000 Hz

Repeat accuracy of

 Precise start/stop 

(terminals 18, 19)

• ± 0.5 msec

System response time (terminals 18, 19, 27, 29, 33)

• 26.6 msec

Speed control range (open-loop)

1:10 of synchronous speed

Speed control range (closed-loop)

1:120 of synchronous speed

Speed accuracy (open-loop)

150 - 3600 rpm: Max. error of ±23 rpm

Speed accuracy (closed-loop)

30 - 3600 rpm: Max. error of ±7.5 rpm

All control characteristics are based on a 4-pole asynchronous motor

Surroundings:

Enclosure

IP 20

Enclosure with options

NEMA 1

Vibration test

0.7 g

Max. relative humidity

5%-93% during operation

Ambient temperature

Max. 113° F [45° C] (24-hour average max. 104° F [40° C])

Derating for high ambient temperature, see special conditions in the Design Guide

Min. ambient temperature during full-scale operation

32° F [0° C]

Min. ambient temperature at reduced performance

14° F [-10° C]

Temperature during storage/transport

-13° - +149°/158° F [-25° - +65°/70° C]

Max. altitude above sea level

3,280 ft [1,000 m]

Derating for high air pressure, see special conditions in the Design Guide

EMC standards, Emission

EN 61081-2, EN 61800-3, EN 55011

EMC standards, Immunity

EN 50082-1/2, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN

61000-4-6, EN 61800-3

See section on special conditions in the Design Guide

VLT

®

 2800 Series

108 

 MG.27.A2.22 - VLT

®

 is a registered Danfoss trademark

Содержание VLT 2800 Series

























































































































Отзывы:

Нет отзывов