Danfoss VLT 2800 Series Скачать руководство пользователя страница 66

Страница: 66 / 120

Alarm or warning

: the output is activated by an alarm

or warning.

Current limit

: the output current is higher than the value

programmed in parameter 221 Current limit I

LIM

Alarm

: the output is activated by an alarm.

Output frequency higher than f

LOW

the output frequen-

cy is higher than the value set in parameter 225

Warning: Low frequency, f

LOW

Output frequency lower than f

HIGH

the output frequen-

cy is lower than the value set in parameter 226

Warn-

ing: High frequency, f

HIGH

Output current higher than I

LOW

: the output current is

higher than the value set in parameter 223

Warning:

Low current, I

LOW

Output current lower than I

HIGH

: the output current is

lower than the value set in parameter 224

Warning:

High current, I

HIGH

Feedback higher than FB

LOW

: the feedback value is

higher than the value set in parameter 227

Warning:

Low feedback, FB

LOW

Feedback lower than FB

HIGH

: the feedback value is

lower than the value set in parameter 228

Warning:

High current, I

HIGH

Relay 123

is only used in connection with Profidrive.

Reversing

: the relay output is activated when the di-

rection of motor rotation is counter-clockwise. When
the direction of motor rotation is clockwise, the value
is 0 V DC.

Thermal warning

: above the temperature limit in either

the motor or the adjustable frequency drive, or from a
thermistor connected to a digital input.

Local operation

: the output is active when in parameter

002

Local/remote operation,

Local operation

[1] has

been selected.

Out of the frequency range

: the output frequency is out

of the programmed frequency range in parameters
225 and 226.

Out of the current range

: the motor current is out of the

programmed range in parameters 223 and 224.

Out of the feedback range

: the feedback signal is out

of the programmed range in parameters 227 and 228.

Mechanical brake control

: enables you to control an

external mechanical brake (see section about control
of mechanical brake in the VLT 2800 Design Guide).

327

Pulse/reference feedback

(PULSE REF/FB MAX)

Value:

150 - 67600 Hz

5000 Hz

Function:

This parameter is used for setting the signal value that
corresponds to the maximum value set in parameter

205

Maximum reference, Ref

MAX

or to the maximum

feedback value set in parameter 415

Maximum feed-

back, FB

MAX

Description of choice:

Set the required pulse reference or pulse feedback to
be connected to terminal 33.

328

Maximum Pulse 29

(MAX PULSE 29)

Value:

150 - 67600 Hz

5000 Hz

Function:

This parameter is used for setting the signal value that
corresponds to the maximum value set in parameter
205

Maximum reference, Ref

MAX

or to the maximum

feedback value set in parameter 415

Maximum feed-

back, FB

MAX

NOTE

Only relevant for DeviceNet. See
MG90BXYY for further information.

341

Digital / pulse output terminal 46

(DO 46 FUNCTION)

Value:

Unit ready (Unit ready)

[0]

Parameter [0] - [20] see parameter 323

Pulse reference (PULSE REFERENCE)

[21]

Parameter [22] - [25] see parameter 323

VLT

2800 Series

= factory setting, () = display text, [] = value for use in communication via serial communication port

MG.27.A2.22 - VLT

is a registered Danfoss trademark

Содержание VLT 2800 Series

























































































































Результаты поиска

Содержание VLT 2800 Series

Отзывы:

Danfoss VLT 2800 Series, Общее руководство пользователя, Страница: 66 / 120

Результаты поиска

Содержание VLT 2800 Series

Отзывы: