Danfoss VLT 2800 Series Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 120

Danfoss VLT 2800 Series Скачать руководство пользователя страница 88

508

Selection of preset ref.

(PRES.REF. SELECT)

Value:

Digital input (DIGITAL INPUT)

[0]

Serial comunication (SERIAL PORT)

[1]

Logic and (LOGIC AND)

[2]

Logic or (LOGIC OR)

[3]

Function:

See function description of parameter 502

Coasting

stop.

Description of choice:

Preset references via serial communication are active

when parameter 512

Telegram profile

is set to

FC pro-

tocol

[1].

509

Bus jog 1 (BUS JOG 1 FREQ.)

510

Bus jog 2 (BUS JOG 2 FREQ.)

Value:

0.0 - par. 202

Output frequency high

limit

10,0 Hz

Function:

If parameter 512

Telegram Profile

shows the selection

Profidrive

[0], two fixed speeds (Jog 1 or Jog 2) can be

selected via the serial port.
The function is the same as in parameter 213

Jog fre-

quency

.

Description of choice:

Jog frequency f

JOG

can be selected between 0 Hz and

f

MAX

.

512

Telegram Profile

(Telegram Profile)

Value:

Profidrive (Profidrive)

[0]

FC protocol (FC protocol)

[1]

Function:

It is possible to choose between two different control
word profiles.

Description of choice:

Select the desired control word profile.
See

Serial port for VLT 2800

for further details of con-

trol word profiles.

513

Bus time interval

(BUS TIMEOUT TIME)

Value:

1 - 99 sec.

1 sec.

Function:

In this parameter it is possible to preset the maximum
time expected to elapse between receipt of two con-
secutive telegrams. If this time is exceeded, the serial
communication is assumed to have stopped and the
desired reaction is preset in parameter 514

Bus time

interval function

.

Description of choice:

Preset the required time.

514

Bus time interval function

(BUS TIMEOUT FUNC)

Value:

Off (off)

[0]

Freeze output frequency (FREEZE OUTPUT)

[1]

Stop (STOP)

[2]

Jogging (JOGGING)

[3]

Max. speed (MAX SPEED)

[4]

Stop and trip (STOP AND TRIP)

[5]

Function:

In this parameter you can select the required reaction
for the variable frequency drive when the preset time
in parameter 513

Bus time interval

has been excee-

ded. If choices [1] to [5] are activated the output relay
will be deactivated.

Description of choice:

The output frequency of the variable frequency drive
can be frozen at the present value, stop the motor, be
frozen at parameter 213

Jogging frequency

, be frozen

at parameter 202

Output frequency, high limit f

MAX

or

stop and activate a cut out.

VLT

®

2800 Series

= factory setting, () = display text, [] = value for use in communication via serial communication port

88

MG.27.A2.22 - VLT

®

is a registered Danfoss trademark

«
...
86
87
88
89
90
...
»

Содержание VLT 2800 Series

























































































































Отзывы:

Нет отзывов