manualshive.com logo in svg

Danfoss VLT 2800 Series, Общее руководство пользователя, Страница: 69 / 120

Поделиться
Скачать
Danfoss VLT 2800 Series Скачать руководство пользователя страница 69

Special functions

400

Brake function

(Brake function)

Value:

Off (off)

[0]

Resistor brake
(Resistor)

[1]

AC brake (AC Brake)

[4]

Load sharing (load sharing)

[5]

Factory setting depends on unit type.

Function:

Resistor brake

 [1] is selected if the adjustable frequen-

cy drive has an integral brake transistor and brake
resistor is connected to terminals 81, 82. A higher in-
termediate circuit voltage is permitted during braking
(generated operation) when a brake resistor is con-
nected.

AC brake

 [4] can be selected to improve braking with-

out using brake resistors. Please note that 

AC brake

[4] is not as effective as 

Resistor brake

 [1].

Description of choice:

Select 

Resistor brake

 [1] if a brake resistor is connec-

ted.
Select 

 AC brake

 [4] if short-term generated loads oc-

cur. See parameter 144 

Gain AC brake

 to set the brake.

Select 

Load sharing

 [5] if this is used.

NOTE

A change of selection will not become ac-
tive until the mains voltage has been dis-
connected and reconnected.

405

Reset function

(reset mode)

Value:

Manual reset (manual reset)

[0]

Automatic reset x 1
(AUTOMATIC x 1)

[1]

Automatic reset x 3
(AUTOMATIC x 3)

[3]

Automatic reset x 10

[10]

(AUTOMATIC x 10)

Reset at power-up
(RESET AT POWER UP)

[11]

Function:

This parameter makes it possible to select whether re-
set and restart after a trip are to be manual or whether
the adjustable frequency drive is to be reset and re-
started automatically. Furthermore, it is possible to
select the number of times a restart is to be attempted.
The time between each attempt is set in parameter 406

Automatic restart time

.

Description of choice:

If 

Manual reset

 [0] is selected, reset is to be carried out

via the [STOP/RESET] key, a digital input or serial
communication. If the adjustable frequency drive is to
carry out an automatic reset and restart after a trip,
select data value [1], [3] or [10].
If 

Reset at power-up

 [11] is selected, the adjustable

frequency drive will carry out a reset if there has been
a fault in connection with the mains failure.

The motor may start without warning.

406

Automatic restart time

(autorestart time)

Value:

0 - 10 sec.

 5 sec.

Function:

This parameter allows setting of the time from tripping
until the automatic reset function begins. It is assumed
that automatic reset has been selected in parameter
405 

 Reset function

.

Description of choice:

Set the required time.

409

Trip delay overcurrent, I

LIM

(trip delay cur.)

Value:

0 - 60 sec. (61=OFF)

 OFF

VLT

®

 2800 Series

  = factory setting, () = display text, [] = value for use in communication via serial communication port

MG.27.A2.22 - VLT

®

 is a registered Danfoss trademark 

 69

Prog

rammi

ng

Содержание VLT 2800 Series

























































































































Отзывы:

Нет отзывов