manualshive.com logo in svg

Danfoss VLT 2800 Series, Общее руководство пользователя, Страница: 60 / 120

Поделиться
Скачать
Danfoss VLT 2800 Series Скачать руководство пользователя страница 60

Description of choice:

No operation

 is selected if the adjustable frequency

drive is not to react to signals transmitted to the termi-
nal.

Reset

 resets the adjustable frequency drive after an

alarm; however, a few alarms cannot be reset (trip
locked) without first disconnecting the line supply and
reconnecting it. See table under 

List of warnings and

alarms

. Reset is activated on the leading edge of the

signal.

Coasting stop inverse

 is used for making the adjustable

frequency drive "let go" of the motor immediately (out-
put transistors are "turned off"), which means that the
motor runs freely to a stop. Logic '0' leads to coasting
to stop.

Reset and coasting inverse

 are used to activate motor

coast simultaneously with reset. Logical '0' means mo-
tor coast stop and reset. Reset is activated on the
falling edge.

Quick stop inverse

 is used for activating the quick stop

ramp-down set in parameter 212 

Quick stop ramp-

down time.

 Logic '0' leads to quick stop.

DC braking inverse

 is used for stopping the motor by

energizing it with a DC voltage for a given time; see

parameters 126, 127 and 132 

DC brake

. Please note

that this function is only active if the value in parameter

126 

DC braking time

 and 132

 DC brake voltage

 is dif-

ferent from 0. Logic '0' leads to DC braking.

Stop inverse

, a logic '0' means that the motor speed is

ramped down to stop via the selected ramp.

None of the stop commands mentioned
above are to be used as repair switches.
Note that the adjustable frequency drive
has more voltage inputs than L1, L2 and
L3 when the DC bus terminals are used.
Make sure that all voltage inputs are dis-
connected and that the prescribed time (4
minutes.) has passed before repair work
is commenced.

Start

 is selected if a start/stop command is required.

Logic '1' = start, logic '0' = stop.

Latched start -

 if a pulse is applied for at least 14 ms,

the adjustable frequency drive will start the motor, pro-
vided no stop command has been given. The motor
can be stopped by briefly activating 

Stop inverse

.

Reversing

 is used for changing the direction of rotation

of the motor shaft. Logic '0' will not lead to reversing.
Logic '1' will lead to reversing. The reverse signal only
changes the direction of rotation, it does not activate
the start. Is not active at 

Process regulation, closed-

loop

. See also parameter 200 

Output frequency range/

direction

.

Reversing and start

 is used for start/stop and for re-

versing with the same signal. No active start command
is allowed at the same time. Acts as latch start revers-
ing, provided latch start has been chosen for terminal

18. Is not active for 

Process regulation, closed-loop

.

See also parameter 200 

Output frequency range/di-

rection

.

Start clockwise

 is used if you want the motor shaft only

to be able to rotate clockwise when started. Should not
be used for 

Process regulation, closed-loop

.

Start counter-clockwise

 is used if you want the motor

shaft only to be able to rotate counter-clockwise when
started. Should not be used for 

Process regulation,

closed-loop

. See also parameter 200 

Output frequency

range/direction

.

Jog is used to override the output frequency to the jog
frequency set in parameter 213 

Jog frequency

. Jog is

active regardless of whether a start command has
been given, yet not when 

Coast stop

, 

Quick stop 

or 

DC

braking

 are active.

Freeze reference

 freezes the present reference. The

reference can now only be changed via 

Speed up

 and

Slow

. If 

freeze reference

 is active, it will be saved after

a stop command and in the event of line failure.

Freeze output

 freezes the present output frequency (in

Hz). The output frequency can now only be changed
via 

Speed up

 and 

Slow

.

VLT

®

 2800 Series

  = factory setting, () = display text, [] = value for use in communication via serial communication port

60 

 MG.27.A2.22 - VLT

®

 is a registered Danfoss trademark

Содержание VLT 2800 Series

























































































































Отзывы:

Нет отзывов