Danfoss VLT 2800 Series Скачать руководство пользователя страница 52

Страница: 52 / 120

References & Limits

200

Output frequency range

(OUT FREQ. RNG/ROT)

Value:

Only clockwise, 0 - 132 Hz
(132 Hz CLOCKWISE)

[0]

Both directions, 0 - 132 Hz
(132 Hz BOTH DIRECT)

[1]

Counter-clockwise only, 0 - 132 Hz
(132 Hz COUNTER CLOCK)

[2]

Clockwise only, 0 - 1,000 Hz
(1,000 Hz CLOCK WISE)

[3]

Both directions, 0 - 1,000 Hz
(1,000 Hz BOTH DIRECT)

[4]

Counter-clockwise only, 0 - 1,000 Hz
(1,000 Hz COUNTER CLOCK)

[5]

Function:

This parameter guarantees protection against unwan-
ted reversing. Furthermore, the maximum output fre-
quency that is to apply regardless of the settings of
other parameters can be selected. This parameter has

no function if

Process regulation, closed-loop

has been

selected in parameter 100

Configuration

Description of choice:

Select the required direction of rotation as well as the
maximum output frequency. Please note that if

Clock-

wise only

[0]/[3] or

Counter-clockwise only

[2]/[5] is

selected, the output frequency will be limited to the
range f

MIN

-f

MAX

. If

Both directions

[1]/[4] is selected, the

output frequency will be limited to the range ± f

MAX

(the

minimum frequency is of no significance).

201

Output frequency low limit, f

MIN

(MIN OUTPUT FREQ)

Value:

0.0 - f

MAX

0.0 Hz

Function:

In this parameter, a minimum motor frequency limit
can be selected that corresponds to the minimum

speed at which the motor is allowed to run. If

Both di-

rections

has been selected in parameter 200

Output

frequency range

, the minimum frequency is of no sig-

nificance.

Description of choice:

The value chosen can range from 0.0 Hz to the fre-
quency set in parameter 202

Output frequency high

limit, f

MAX

202

Output frequency high limit, f

MAX

(max. output freq)

Value:

MIN

- 132/1,000 Hz (par. 200

Output fre-

quency range

)

132 Hz

Function:

In this parameter, a maximum output frequency limit
can be selected that corresponds to the highest speed
at which the motor is allowed to run.

NOTE

The output frequency of the adjustable
frequency drive can never assume a value
higher than 1/10 of the switching frequen-
cy (parameter 411

Switching frequency

Description of choice:

A value can be selected from f

MIN

to the value chosen

in parameter 200

Output frequency range

VLT

2800 Series

= factory setting, () = display text, [] = value for use in communication via serial communication port

MG.27.A2.22 - VLT

is a registered Danfoss trademark

Содержание VLT 2800 Series

























































































































Результаты поиска

Содержание VLT 2800 Series

Отзывы:

Danfoss VLT 2800 Series, Общее руководство пользователя, Страница: 52 / 120

Результаты поиска

Содержание VLT 2800 Series

Отзывы: