Danfoss VLT 2800 Series Скачать руководство пользователя страница 89

Страница: 89 / 120

515-544 Data readout

Value:

Par.
no.

Description

Display text

Unit

Update
interval

515

Res. reference

(REFERENCE %)

516

Res. reference [Unit]

(REFERENCE [UNIT])

Hz, rpm

517

Feedback [Unit]

(FEEDBACK [UNIT])

Par. 416

518

Frequency

(FREQUENCY)

519

Frequency x scale

(FREQUENCY X SCALE)

520

Motor current

(MOTOR CURRENT)

Amp

521

Torque

(TORQUE)

522

Power[kW]

(POWER (KW))

523

Power[HP]

(POWER (HP))

524

Motor voltage

(MOTOR VOLTAGE)

525

DC-link voltage

(DC LINK VOLTAGE)

526

Thermal load motor

(MOTOR THERMAL)

527

Thermal load inverter

(INV. THERMAL)

528

Digital input

(DIGITAL INPUT)

Bin

529

Term.53, analogue input

(ANALOG INPUT 53)

531

Term.60, analogue input

(ANALOG INPUT 60)

532

Pulse reference

(PULSE REFERENCE)

533

External ref.

(EXT. REF.%)

534

Status word, Hex

(STATUS WORD)

Hex

535

Bus feedback 1

(BUS FEEDBACK1)

Hex

537

Inverter temperature

(INVERTER TEMP.)

°C

538

Alarm word

(ALARM WORD)

Hex

539

Control word

(CONTROL WORD)

Hex

540

Warning word

(WARN. WORD)

Hex

541

Extended status word

(STATUS WORD)

Hex

544

Pulse count

(PULSE COUNT)

Function:

These parameters can be read out via the serial com-
munication port and the LCP display. See also param-

eters 009-012

Display readout

NOTE

Parameters 515-541 can only be read out
via an LCP control unit.

Description of choice:

Resulting reference %, parameter 515:

Gives the resulting reference as a percentage in the
range from Minimum reference, Ref

MIN

to Maximum

reference, Ref

MAX

. See also

Dealing with references

Resulting reference [unit], parameter 516:

Gives the resulting reference in Hz in Open loop (pa-
rameter 100). In a closed loop the reference unit is

selected in parameter 416

Process units

Feedback [unit], parameter 517:

Gives the resulting feedback value with the unit/scal-
ing selected in parameters 414, 415 and 416. See also
dealing with feedback.

Frequency [Hz], parameter 518:

Gives the output frequency from the adjustable fre-
quency drive.

Frequency x scaling [-], parameter 519:

corresponds to the present output frequency f

multi-

plied by the factor preset in parameter 008

Display

scaling of output frequency

VLT

2800 Series

= factory setting, () = display text, [] = value for use in communication via serial communication port

MG.27.A2.22 - VLT

is a registered Danfoss trademark

Prog

rammi

Содержание VLT 2800 Series

























































































































Результаты поиска

Содержание VLT 2800 Series

Отзывы:

Danfoss VLT 2800 Series, Общее руководство пользователя, Страница: 89 / 120

Результаты поиска

Содержание VLT 2800 Series

Отзывы: