Danfoss VLT 2800 Series Скачать руководство пользователя страница 101

Страница: 101 / 120

Alarm 44, internal fault number 7: Minimum software
version of control card or BMC.

Alarm 45, internal fault number 8: I/O fault (digital in-
put/output, relay or analog input/output).

NOTE

When restarting after an alarm 38-45, the
adjustable frequency drive will display an
alarm 37. In parameter 615 the actual
alarm code can be read.

ALARM 50: AMT not possible

One of the following three possibilities can occur:

The calculated R

value falls outside permit-

ted limits.

The motor current in at least one of the motor
phases is too low.

The motor in use is too small for AMT calcu-
lations to be performed.

ALARM 51: AMT Fault regarding nameplate data

There is inconsistency between the registered motor
data. Check the motor data for the relevant setup.

ALARM 52: AMT missing motor phase

The AMT function has detected a missing motor
phase.

ALARM 55: AMT timeout

Calculations are taking too long, possibly due to noise
on the motor cables.

ALARM 56: AMT warning during AMT

A adjustable frequency drive warning is given while
AMT is being performed.

WARNING 99: Locked

See parameter 18.

Alarm/warning limits:

Without brake

With brake

Without brake

With brake

VLT 2800

1 / 3 x 200 - 240 V
[VDC]

3 x 380 - 480 V
[VDC]

Undervoltage

215

410

Voltage warning low

230

440

Voltage warning high

385

400

765

800

Overvoltage

410

820

The voltages stated are the intermediate circuit volt-
age of the adjustable frequency drive with a tolerance
of ± 5 %. The corresponding line voltage is the inter-
mediate circuit voltage divided by 1,35.

VLT

2800 Series

MG.27.A2.22 - VLT

is a registered Danfoss trademark

101

All a

bou

VLT 2

800

Содержание VLT 2800 Series

























































































































Результаты поиска

Содержание VLT 2800 Series

Отзывы:

Danfoss VLT 2800 Series, Общее руководство пользователя, Страница: 101 / 120

Результаты поиска

Содержание VLT 2800 Series

Отзывы: