DANA SPICER PACCAR 220ev Скачать руководство пользователя

Страница: 6 / 761

Safety Warnings

Warning:

Charger cables must be

connected positive to positive (+ to +) and

negative to negative (- to -). If connected

improperly, LV batteries could explode.

Failure to comply may result in personal

injury, death, equipment, or property

damage.

Warning:

Always ensure the LV battery

charger is OFF before connecting or

disconnecting the cable clamps. To reduce

the danger of explosions and resulting

death or personal injury, do not connect or

disconnect charger cables while the charger

is operating.

Warning:

Never use a fast charger as a

booster to start the system. This can

seriously damage sensitive electronic

components such as relays, radio, as well

as the LV battery charger. Fast charging a

LV battery is dangerous and should only be

attempted by a competent mechanic with

the proper equipment.

Warning:

LV batteries contain acid that can

burn and gasses that can explode. Ignoring

safety procedures may result in death,

personal injury, equipment, or property

damage.

Warning:

Never remove or tamper with LV

battery caps. Ignoring this could allow LV

battery acid to contact the eyes, skin,

fabrics, or painted surfaces. Failure to

comply may result in death, personal injury,

equipment, or property damage. Be careful

that metal tools (or any metal in contact with

the positive terminal) do not contact the

positive battery terminal and any other

metal on the vehicle at the same time.

Remove metal jewelry and avoid leaning

over the LV battery.

Caution:

Using higher voltage booster for

the LV batteries will cause expensive

damage to sensitive electronic components

such as relays, sensors, and control units.

Always charge the LV batteries at the

proper voltage. Failure to comply may result

in equipment damage.

Caution:

Do not modify or improperly repair

the vehicle’s electrical system or electric

powertrain. All electrical repairs should be

performed by an authorized dealer.

Improper repair or modifications will void

the warranty and/or cause serious damage

to your vehicle.

Additional Information

Note:

Review the warranty policy before

performing any maintenance procedures.

An extended warranty may be voided if

unauthorized maintenance is performed

during this period.

Note:

The description and specifications

contained in the service publication are

current at the time of printing.

Note:

Dana reserves the right to

discontinue or modify its models and/or

procedures and to change specifications at

any time without notice.

Note:

Always use genuine Dana

replacement parts.

Note:

Every effort has been made to

ensure the accuracy of all information in this

guide. However, Dana Commercial Vehicle

Systems Division makes no express or

implied warranty or representation based on

the enclosed information.

Any errors or omissions may be reported to:

Dana Commercial Vehicle Systems

3939 Technology Drive

Maumee, OH 43537

Содержание SPICER PACCAR 220ev


























































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SPICER PACCAR 220ev

Отзывы:

Похожие инструкции для SPICER PACCAR 220ev

Бренды по названию

Популярные бренды

DANA SPICER PACCAR 220ev, Руководство по устранению неисправностей

Результаты поиска

Содержание SPICER PACCAR 220ev

Отзывы:

Похожие инструкции для SPICER PACCAR 220ev

Бренды по названию

Популярные бренды