background image

 

 

 

 

 

277 

Troubleshooting 

F0097, F0098 (Fault Reason 3)  

Error Description 

Possible Causes 

Possible Solutions 

Traction inverter has limited 

regenerative braking (F0097) or 

traction (F0098) due to overspeed. 

1)  Adverse driving conditions. 

2)  Traction inverter software or 

calibration error. 

3)  Loss of continuity between 

traction inverter and speed 

sensor due to defective LV 

connector or harness. 

4)  Traction inverter internal 

failure. 

5)  Motor internal failure. 

 

1)  No action needed. 

2)  Update traction inverter 

software and calibration. 

3)  Replace LV connector or 

harness per Service Manual. 

4)  Replace traction inverter. 

5)  Replace motor. 

 

 

This error can occur if the vehicle is traveling over 70 

mph or on a steep slope. In these cases, the vehicle 

is behaving normally and no troubleshooting is 

needed. 

 

 

 

Propulsion System faults may also be 

investigated and resolved using the ODIN 

tool and the TM4 SUMO Powertrain 

Troubleshooting Guide. 

 

 

 

 

 

 

Содержание SPICER PACCAR 220ev


























































































































































































































































































































































































































































































































































































































































































































































































Отзывы: