Dalsa Genie Nano-CXP страница 26 Скачать руководство пользователя | Manualshive

Страница: 26 / 143

background image

24

•

Nano-CXP Installation

Genie Nano-

CXP Series™

Nano-CXP Installation

If you are familiar with CoaXPress cameras and Teledyne DALSA frame grabbers, follow these steps
to quickly install and acquire images with Genie Nano-CXP and the CamExpert tool provided with
Sapera LT in a Windows OS system.

Quick Start (using a Teledyne DALSA Frame Grabber)

•

Install Sapera 8.41 (or later). Use the Full SDK version with support for Teledyne DALSA frame
grabber boards.

•

Install the Teledyne DALSA CoaXPress frame grabber board along with its driver.

•

Start CamExpert. The plug-and-play feature of CXP frame grabber and camera will
automatically configure frame buffer, data lanes, and frame rate parameters to match the
Nano-CXP model being used. At this time do not configure for an external trigger.

•

Connect the Nano-CXP with 4 camera cables. The Teledyne DALSA CXP frame grabber supports
PoCXP (power over CoaXPress) for a simple camera power solution.

•

Enable PoCXP by its frame grabber feature. If not using PoCXP connect a power supply to the

Nano-CXP via its

•

When the Nano-CXP boots, CamExpert will read and display the camera features available with
that model.

•

The Nano-CXP status

LED has changed to flashing green

, indicating it is in free running

acquisition mode. See

on Power Up for all status LED conditions.

•

From the Nano-CXP Image Format Feature Category, select the

Moving Grey Diagonal Ramp

test pattern from the

Test Image Selector

Parameter.

•

Click grab. You will see the moving pattern in the CamExpert display window.

•

If a camera lens is attached, turn off the test pattern and grab live again. Adjust the lens
aperture plus Focus, and/or adjust the Nano

Exposure Time and frame rate

as required.

General Installation Overview

Connecting a Nano-CXP to a frame grabber is similar whether using a Teledyne DALSA frame
grabber board with Sapera LT SDK or a third-party frame grabber with its own SDK.

Camera Firmware Updates

Under Windows, the user can upload new firmware, using the

File Access Control

features provided

by the Sapera CamExpert tool.
Download the latest firmware version released from the Teledyne DALSA support web page:

http://www.teledynedalsa.com/imaging/support/downloads/firmware/

«
...
24
25
26
27
28
...
»

Содержание Genie Nano-CXP
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Genie Nano-CXP

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 71

Бренд: Canon Страницы: 414

Бренд: Canon Страницы: 612

Бренд: Canon Страницы: 13

Бренд: Canon Страницы: 350

Бренд: Canon Страницы: 122

EOS Rebel T5i 18-55mm IS STM Kit

Бренд: Canon Страницы: 388

Бренд: Canon Страницы: 11

Бренд: Canon Страницы: 105

Бренд: Canon Страницы: 7

Бренд: Canon Страницы: 14

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 123

Бренд: Canon Страницы: 6

Бренд: Canon Страницы: 213

Бренд: Canon Страницы: 212

Бренд: Canon Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды