Dalsa Genie Nano-CXP Скачать руководство пользователя страница 46

Страница: 46 / 143

•

Feature Descriptions

Genie Nano-

CXP Series™

Output Line Pulse Signal
Activation

outputLinePulseActivation

Specifies the input line activation mode to trigger the
OutputLine pulse.

1.02

Beginner

DFNC

Rising Edge

RisingEdge

Specifies that the trigger is considered valid on the
rising edge of the source signal.

Falling Edge

FallingEdge

Specifies that the trigger is considered valid on the
falling edge of the source signal.

Any Edge

AnyEdge

Specifies that the trigger is considered valid on the
falling or rising edge of the source signal.

Output Line Pulse Delay

outputLinePulseDelay

Sets the delay (in µs) before the output line pulse
signal. Applicable for the OutputLineSource feature.

1.02

Beginner

DFNC

Output Line Pulse Duration

outputLinePulseDuration

Sets the width (duration) of the output line pulse in
microseconds.

1.02

Beginner

DFNC

Output Line Value

outputLineValue

Sets the output state of the selected Line if the
outputLineSoftwareLatchControl = OFF.
OutputLineSource must be SoftwareControlled.

1.02

Beginner

DFNC

Active

Sets the Output circuit to close

Inactive

Sets the Output circuit to open

Line Status All

LineStatusAll

Returns the current status of all available line signals, at
time of polling, in a single bitfield. The order is Line1,
Line2, Line3, ...

1.00

Expert

Line Format

LineFormat

Specify the current electrical format of the selected
physical input or output.

1.00

Invisible

CXP

CxP

The line accepts CXP Trigger packets.

Opto-Coupled

OptoCoupled

The line is opto-coupled.

Line Mode

LineMode

Reports if the physical Line is an Input or Output signal..

1.00

Invisible

Input

The line is an input line.

Output

The line is an output line.

Input Line Detection Level

lineDetectionLevel

Specifies the voltage threshold required to recognize a
signal transition on an input line.

1.00

Invisible

DFNC

Threshold for TTL

Threshold_for_TTL

A signal below 0.8V will be detected as a Logical LOW

and a signal greater than 2.4V will be detected as a
Logical HIGH on the selected input line.

Содержание Genie Nano-CXP
















































































































































Результаты поиска

Содержание Genie Nano-CXP

Отзывы:

Бренды по названию

Популярные бренды

Dalsa Genie Nano-CXP, Руководство пользователя

Результаты поиска

Содержание Genie Nano-CXP

Отзывы:

Бренды по названию

Популярные бренды