Dalsa Genie Nano-CXP Скачать руководство пользователя | Manualshive

Страница: 124 / 143

background image

122

•

Additional Reference Information

Genie Nano-

CXP Series™

The following figure shows the lens image circles relative to Genie Nano-CXP models using the

Teledyne E2V Emerald 37.7M (Four Thirds image sensor format) and 67.1M (APS-C image sensor
format) sensors.

28.96mm minimum

Image Circle

Model 6200

Model 8200

21.72mm minimum

Image Circle

Additional Lens Parameters (application-specific)

There are other lens parameters that are chosen to meet the needs of the vision application. These
parameters are independent of the Nano model (assuming that the Lens Mount and Lens Sensor
Size parameters are correct, as previously covered in this section). A vision system integrator or
lens specialist should be consulted when choosing lenses since there is a trade-off between the

best lenses and cost. An abridged list of lens parameters follows

–

all of which need to be matched

to the application.

•

Focal Length

: Defines the focus point of light from infinity. This parameter is related to the

Nano mount (C or CS mount).

•

Field of View

: A lens is designed to image objects at some limited distance range, at some

positive or negative magnification. This defines the field of view.

•

F-Number (aperture)

: The lens aperture defines the amount of light that can pass. Lenses

may have fixed or variable apertures. Additionally the lens aperture affects Depth of Field
which defines the distance range which is in focus when the lens is focus at some specific
distance.

•

Image Resolution and Distortion

: A general definition of image quality. A lens with poor

resolution seems to never be in focus when used to image fine details.

•

Aberrations (defect, chromatic, spherical)

: Aberrations are specific types of lens faults

affecting resolution and distortion. Lens surface defects or glass faults distort all light or
specific colors. Aberrations are typically more visible when imaging fine details.

•

Spatial Distortions

: Describes non-linear lens distortions across the field of view. Such

distortion limits the accuracy of measurements made with that lens.

«
...
122
123
124
125
126
...
»

Содержание Genie Nano-CXP
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Genie Nano-CXP

Бренд: GE Страницы: 76

POWER series E1486TW

Бренд: GE Страницы: 93

A Series A1456W

Бренд: GE Страницы: 85

Whatman Mini-UniPrep G2

Бренд: GE Страницы: 106

Бренд: Samsung Страницы: 44

GX-20 - Digital Camera SLR

Бренд: Samsung Страницы: 2

Бренд: FALEEMI Страницы: 14

Бренд: AGFA Страницы: 34

Бренд: Vivitar Страницы: 51

Бренд: Grundig Страницы: 98

Бренд: Kodak Страницы: 2

Бренд: CamnSmart Страницы: 10

Бренд: iBeam Страницы: 8

Бренд: Vicon Страницы: 24

Бренд: Sinar Страницы: 20

Бренд: Zxtech Страницы: 23

Бренд: Pilot Electronics Страницы: 6

Бренд: Panasonic Страницы: 520

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды