Dalsa Genie Nano-CXP страница 141 Скачать руководство пользователя | Manualshive

Страница: 141 / 143

background image

Genie Nano-

CXP Series™

Troubleshooting

•

139

Power Failure during a Firmware Update

–

Now What?

Don

’

t panic! There is far greater chance that the host computer OS is damaged during a power

failure than any permanent problems with the Nano. When electrical power returns and the host
computer system has restarted follow this procedure.

•

Connect power to the Nano-CXP. The Nano processor knows that the firmware update failed.

•

The Nano-CXP will boot with the previous version of firmware and will operate normally.

•

The

Nano Self Status

(deviceBISTStatus) will return that the last firmware update failed.

•

Perform the firmware update procedure again.

Cabling and Communication Issues

With only 4 CXP coax cables and possibly an external power supply (if not using PoCXP), possible
cabling issues are limited.

Power supply problems:

•

If using PoCXP power, verify that the frame grabber used has activated its PoCXP source
function. Note that the frame grabber typically requires direct PC power connected to it, as

directed by the grabber’s user man

ual.

•

If using DC supply power via the I/O camera connector, verify the power supply voltage and
I/O cable wiring.

Communication Problems:

•

Use quality DIN 1.0/2.3 coax cables along with quality shielded I/O cables. This can eliminate
issues in a high EMI environment. Purchase CXP cables from certified sources.

•

Use the Log Viewer tool (see point below) for error conditions.

•

Run the Sapera Log Viewer:

Start•Programs•

Teledyne DALSA

•Sapera LT•Tools•Log

Viewer

. Start the Nano-CXP acquisition program, such as CamExpert. Review the log output

for error messages.

Camera is functional, frame rate is as expected, but image is
black

•

Using CamExpert set the Nano-CXP to output its Internal Pattern Generator (with external
trigger Off). This step is typically done for any camera installation to quickly verify the Nano

and its software package.

•

If using an external trigger exposure (via the frame grabber), verify the trigger source rate and
pulse width coming from the grabber parameters.

•

Verify that the lens iris is open.

•

Aim the Nano-CXP at a bright light source.

•

Check that the programmed exposure duration is not too short or set it to maximum.

«
...
139
140
141
142
143
»

Содержание Genie Nano-CXP
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Genie Nano-CXP

Бренд: Samsung Страницы: 98

Бренд: Tamron Страницы: 4

Бренд: Ganz Thermal Страницы: 2

Бренд: Uniden Страницы: 20

Бренд: Sandstrom Страницы: 24

Бренд: Safety Vision Страницы: 20

Бренд: PMD Страницы: 8

VK2-1080MD37PTW

Бренд: Vista Страницы: 15

ALIBI ALI-NS2112VR

Бренд: Observint Страницы: 7

Бренд: Pro-Built Tools Страницы: 24

Бренд: Iget Страницы: 8

Бренд: SunBriteTV Страницы: 41

Бренд: Xblitz Страницы: 17

Бренд: RDS Страницы: 46

Бренд: ACS Страницы: 12

Бренд: Assa Abloy Страницы: 8

Бренд: Cobra Страницы: 2

Бренд: Cobra Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды