Dalsa Genie Nano-CXP Скачать руководство пользователя страница 20

Страница: 20 / 143

•

Nano-CXP Specifications

Genie Nano-

CXP Series™

Nano-CXP Specifications: M6200, C6200

Model specific specifications and response graphics for the Teledyne E2V Emerald (37.7M) series

are provided here. The response curves describe the sensor, excluding lens and light source
characteristics.

Supported Features

M6200

C6200

Resolution

6144 x 6144

(37.7M pixel resolution)

Sensor Name

Teledyne E2V Emerald 36M

Pixel Size

2.5 µm x 2.5 µm

Shutter Type

Full frame electronic global shutter function

Full Well charge

5 ke (max)

4-Lane CXP Configuration

Maximum Frame Rate

Fast readout mode (8-bit only): 40.04 fps

Normal readout mode (8 or 10-bit): 26.76 fps

Horizontal Line Time

Fast readout mode (8-bit only):

Normal readout mode (8 or 10-bit):

3.74 µs
6.08 µs

2-Lane CXP Configuration

Maximum Frame Rate

Normal readout mode

8-bit:

10-bit

20.91 fps
15.75 fps

Horizontal Line Time

Normal readout mode

8-bit:

10-bit

7.77 µs
10.32 µs

1-Lane CXP Configuration

Maximum Frame Rate

Normal readout mode

8-bit:

10-bit

10.26 fps
8.09 fps

Horizontal Line Time

Normal readout mode

8-bit:

10-bit

15.83 µs
20.07 µs

Pixel Format

Mono 8, Mono 10

Bayer 8-bit, Bayer 10-bit

Trigger to Exposure Minimum delay
(

Synchronous Exposure

)

14 µs

Trigger to Exposure Start jitter
(

Synchronous Exposure

)

Up to 1 line time

Trigger to Exposure Start jitter

(Reset Exposure)

0 µs

Exposure Time Minimum

(see “exposureTimeActual” in

Sensor

Control

)

14 µs

Min. Time from End of Exposure to Start of
Next Exposure

Fast readout mode:

Normal readout mode:

68 µs
101 µs

Readout Time

(Horizontal Line Time * NB Lines) in μs

Auto-Brightness

Black offset control

Yes (in DN)

Gain Control

In-sensor Analog Gain (1.0x to 3.0x) in 4 steps

(1.0x, 1.5x, 2x, 3x)

Binning Support

Decimation Support

Defective Pixel Replacement

Yes, up to 4096 positions

Image Correction

Flat Line Correction (Factory and 4 User Defined entries)

Lens Shading correction (Factory and 2 User Defined entry)

Noise Reduction

Содержание Genie Nano-CXP
















































































































































Результаты поиска

Содержание Genie Nano-CXP

Отзывы:

Бренды по названию

Популярные бренды

Dalsa Genie Nano-CXP, Руководство пользователя

Результаты поиска

Содержание Genie Nano-CXP

Отзывы:

Бренды по названию

Популярные бренды