Dalsa Genie Nano-CXP Скачать руководство пользователя страница 77

Страница: 77 / 143

Genie Nano-

CXP Series™

Feature Descriptions

•

Image Format Control Feature Descriptions

Display Name

Feature & Values

Description

Version

& View

Pixel Format

PixelFormat

Format of the pixel provided by the device. Contains all format

information as provided by PixelCoding, PixelSize,
PixelColorFilter, combined in one single value.

1.00

Beginnery

Monochrome 8-Bit

Mono8

Mono8: Monochrome 8-Bit

Monochrome 10-Bit

Mono10

Mono10: Monochrome 10-Bit

BayerGR 8-Bit

BayerGR8

Color camera: BayerGR8

BayerRG 8-Bit

BayerRG8

Color camera: BayerRG8t

BayerGB 8-Bit

BayerGB8

Color camera: BayerGB8

BayerBG 8-Bit

BayerBG8

Color camera: BayerBG8

BayerGR 10-Bit

BayerGR10

Color camera: BayerGR10

BayerRG 10-Bit

BayerRG10

Color camera: BayerRG10

BayerGB 10-Bit

BayerGB10

Color camera: BayerGB10

BayerBG 10-Bit

BayerBG10

Color camera: BayerBG10

Pixel Coding

PixelCoding

Output image pixel coding format of the sensor.

1.00

Guru

Mono

Pixel is monochrome

MonoSigned

Pixel is monochrome and signed

MonoPacked

Pixel is monochrome and packed

Raw Bayer

Raw

Pixel is raw Bayer

Pixel Size

PixelSize

Total size in bits of an image pixel.

1.00

Guru

8 Bits/Pixel

Bpp8

Bpp8: 8 bits per pixel

10 Bits/Pixel

Bpp10

Bpp10: 10 bits per pixel

Horizontal Offset

OffsetX

Horizontal offset from the Sensor Origin to the Region Of
Interest (in pixels).

1.00

Beginner

Vertical Offset

OffsetY

Vertical offset from the Sensor Origin to the Region Of Interest
(in Lines).

1.00

Beginner

Width

Width of the Image provided by the device (in pixels).

1.00

Beginner

Height

Height of the Image provided by the device Beginner

1.00

Beginner

Multiple ROI Mode

multipleROIMode

Enable the Multiple ROI (Region of Interest) per image feature.
The ROI Count is set by the Multiple ROI Count feature.

1.03

Guru

DFNC

Off

Single ROI per image.

Active

The ROI per image feature is active.

ROI Count Horizontal

multipleROICountHorizontal

Specifies the number of ROI (Region of Interest) available for
the X axis.

1.03

Expert

DFNC

ROI Count Vertical

multipleROICountVertical

Specifies the number of ROI (Region of Interest) available for
the Y axis.

1.03

Expert

DFNC

ROI Count

multipleROICount

Specifies the number of possible ROI (Region of Interest)
available in an acquired image. One is minimum, while the
maximum is device specific. < RO >

1.03

Expert

DFNC

Содержание Genie Nano-CXP
















































































































































Результаты поиска

Содержание Genie Nano-CXP

Отзывы:

Бренды по названию

Популярные бренды

Dalsa Genie Nano-CXP, Руководство пользователя

Результаты поиска

Содержание Genie Nano-CXP

Отзывы:

Бренды по названию

Популярные бренды