Dalsa Genie Nano-CXP страница 70 Скачать руководство пользователя

Страница: 70 / 143

•

Feature Descriptions

Genie Nano-

CXP Series™

Cycling Preset Mode Control Feature Descriptions

Display Name

Feature & Values

Description

Device

Version

& View

Cycling Preset Mode

cyclingPresetMode

Sets the Cycling Presets module mode.

1.02

Expert

DFNC

Off

Disable the Cycling Preset module.

Active

Enable the Cycling Preset module.

Cycling Preset Count

cyclingPresetCount

Specifies the number of Presets to use.

1.02

Expert

DFNC

Cycling Preset Incremental
Source

cyclingPresetIncrementalSource

Specifies the source that increments the currently
active cycling preset.

1.02

Expert

DFNC

None

Feature cyclingPresetCurrentActiveSet is used to select
the current active set.

Valid Frame Trigger

ValidFrameTrigger

Increment on a Valid Frame Trigger

Counter 1 End

Counter1End

Increment on the end of Counter 1.

Start of Frame

StartOfFrame

Increment on the Start of Frame event

Trigger Input Line Activation

cyclingPresetIncrementalActivation

Select the activation mode for the selected Input Line
source. This is applicable only for external line inputs.

1.02

Expert

DFNC

Rising Edge

RisingEdge

The source is considered valid on the rising edge of
the line source signal (after being processed by the
line inverter feature).

Falling Edge

FallingEdge

The source is considered valid on the falling edge of
the line source signal (after being processed by the
line inverter feature).

Any Edge

AnyEdge

The source is considered valid on any edge (falling or
rising) of the line source signal (after being processed
by the line inverter feature).

Cycling Preset Repeater

cyclingPresetRepeater

Specifies the required number of cycling preset
increment events (generated by the Cycling Preset
Incremental Source) to increment the index of the
Cycling Preset Current Active Set.

1.02

Expert

DFNC

Cycling Preset Reset Source

cyclingPresetResetSource

Specifies the source that resets the currently active
preset. On reset the current preset index is set to 1

1.02

Expert

DFNC

Valid Frame Trigger

ValidFrameTrigger

Reset when a Valid Frame Triggers occurs.

Counter 1 End

Counter1End

Reset when counter 1 ends.

Timer 1 End

Timer1End

Reset when Timer 1 ends.

Acquisition End

EndOfAcquisition

Use End of Acquisition as the reset source. An End of
Acquisition occurs on acquisition stop.

Software

Use a software command as the reset source.

Cycling Preset Reset Cmd

cyclingPresetResetCmd

Reset the position of the preset cycling to 1 and the
count to 0.

1.02

Guru

DFNC

Cycling Preset Current Active
Set

cyclingPresetCurrentActiveSet

Returns the index of the currently active cycling
preset.

1.02

Guru

DFNC

Cycling Preset ROI Source

cyclingPresetRoiPositionSource

Specifies the source that cycles the ROI position
(availability is sensor dependent).

1.02

Expert

DFNC

In-Sensor

Sensor

The sensor cycles the ROI position.

Содержание Genie Nano-CXP
















































































































































Результаты поиска

Содержание Genie Nano-CXP

Отзывы:

Похожие инструкции для Genie Nano-CXP

Бренды по названию

Популярные бренды

Dalsa Genie Nano-CXP, Руководство пользователя

Результаты поиска

Содержание Genie Nano-CXP

Отзывы:

Похожие инструкции для Genie Nano-CXP

Бренды по названию

Популярные бренды