Dalsa Genie Nano-CXP Скачать руководство пользователя | Manualshive

Страница: 22 / 143

background image

20

•

Nano-CXP Specifications

Genie Nano-

CXP Series™

Nano-CXP Specifications: M8200, C8200

Model specific specifications and response graphics for the Teledyne E2V Emerald (67.1M) series
are provided here. The response curves describe the sensor, excluding lens and light source
characteristics.

Supported Features

M8200

C8200

Resolution

8192 x 8192

(67.1M pixel resolution)

Sensor Name

Teledyne E2V Emerald 67M

Pixel Size

2.5 µm x 2.5 µm

Shutter Type

Full frame electronic global shutter function

Full Well charge

5 ke (max)

4-Lane CXP Configuration

Maximum Frame Rate

Fast readout mode (8-bit only): 30.0 fps

Normal readout mode (8 or 10-bit): 20.1 fps

Horizontal Line Time

Fast readout mode (8-bit only):

Normal readout mode (8 or 10-bit):

4.06 µs
6.08 µs

2-Lane CXP Configuration

Maximum Frame Rate

Normal readout mode

8-bit:

10-bit:

15.7 fps
11.8 fps

Horizontal Line Time

Normal readout mode

8-bit:

10-bit:

7.78 µs
10.33 µs

1-Lane CXP Configuration

Maximum Frame Rate

Normal readout mode

8-bit:

10-bit:

7.70 fps
6.07 fps

Horizontal Line Time

Normal readout mode

8-bit:

10-bit:

15.85 µs
20.10 µs

Pixel Format

Mono 8, Mono 10

Bayer 8-bit, Bayer 10-bit

Trigger to Exposure Minimum delay
(

Synchronous Exposure

)

14 µs

Trigger to Exposure Start jitter
(

Synchronous Exposure

)

Up to 1 line time

Trigger to Exposure Start jitter

(Reset Exposure)

0 µs

Exposure Time Minimum

(see “exposureTimeActual” in

14 µs

Min. Time from End of Exposure to Start of
Next Exposure

Fast readout mode:

Normal readout mode:

68 µs
101 µs

Readout Time

(Horizontal Line Time * NB Lines) in μs

Auto-Brightness

No

Black offset control

Yes (in DN)

Gain Control

In-sensor Analog Gain (1.0x to 3.0x) in 4 steps

(1.0x, 1.5x, 2x, 3x)

Binning Support

No

Decimation Support

No

Defective Pixel Replacement

Yes, up to 4096 positions

Image Correction

Flat Line Correction (Factory and 4 User Defined entries)

Lens Shading correction (Factory and 2 User Defined entry)

Noise Reduction

Image Flip Support

No

«
...
20
21
22
23
24
...
»

Содержание Genie Nano-CXP
















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Genie Nano-CXP

Бренд: Canon Страницы: 21

Бренд: Canon Страницы: 308

Бренд: Canon Страницы: 212

EOS 7D Mark II (G)

Бренд: Canon Страницы: 26

Бренд: Canon Страницы: 15

Бренд: Canon Страницы: 125

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 24

Бренд: Canon Страницы: 170

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 144

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 148

EOS 5D Mark III

Бренд: Canon Страницы: 24

Бренд: Canon Страницы: 164

EOS 7D Mark II (G)

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

EOS Rebel SL1 18-55mm IS STM Kit

Бренд: Canon Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды