Dalsa Genie Nano-CXP страница 67 Скачать руководство пользователя

Страница: 67 / 143

Genie Nano-CXP Ser

ies™

Feature Descriptions

•

Monochrome Defective Pixel Replacement Algorithm Description

The replacement algorithm follows a few basic rules as defined below, which in general provides
satisfactory results.

Single bad pixel in a sensor line with a good adjacent pixel

•

A defective pixel is replaced by the following good pixel if previous pixel is bad or not existent.

•

Or a defective pixel is replaced by the previous good pixel.

Sensor Row

pix1

pix2

pix3

pix5

pix6

pix7

pix4

pix0

Bad pixel in a sensor line with bad adjacent pixels

•

Replace bad pixel with the corresponding pixel of the previous line.

•

Do nothing when the neighboring pixels are also bad.

Sensor Row

“n

”

pix1

pix2

pix3

pix5

pix7

pix0

pix1

pix2

pix3

pix5

pix6

pix7

pix4

pix0

pix4

pix6

Sensor Row

“n”

Remains

Defective

Содержание Genie Nano-CXP
















































































































































Результаты поиска

Содержание Genie Nano-CXP

Отзывы:

Похожие инструкции для Genie Nano-CXP

Бренды по названию

Популярные бренды

Dalsa Genie Nano-CXP, Руководство пользователя

Результаты поиска

Содержание Genie Nano-CXP

Отзывы:

Похожие инструкции для Genie Nano-CXP

Бренды по названию

Популярные бренды