Dalsa Genie Nano-CXP, Руководство пользователя

Страница: 45 / 143

Genie Nano- CXP Series™ Feature Descriptions • 43
Trigger Overlap
TriggerOverlap States if a trigger overlap is permitted with the Active
Frame readout signal. This feature defines if a new valid
trigger will be accepted (or latched) for a new frame.
1.00
Guru
Off Off No trigger overlap is permitted.
Readout Readout
Trigger is accepted immediately after the start of the
readout.
Line Selector LineSelector
Selects the physical line (or pin) of the external device
connector to configure.
1.00
Beginner
CXP CXP Select the CXP trigger.
Line 1 Line1 Index of the physical and associated I/O control block to
use. Pin 5 is the Input Signal and Pine 3 is the common
Ground on the
I/O connector .
Line 2 Line2
Index of the physical and associated I/O control block to
use. Pin 7 is the Input Signal and Pine 3 is the common
Ground on the
I/O connector .
Line Status LineStatus
Returns the current status of the selected input or
output line.
1.00
Expert
False The Line is logic LOW
True The Line is logic HIGH
Line Inverter LineInverter
Control to invert the polarity of the selected input or
output line signal.
1.00
Beginner
False / True
Input Line Debouncing
Period
lineDebouncingPeriod
Specifies the minimum delay before an input line voltage
transition is recognizing as a signal transition.
1.00
Beginner
DFNC
Output Line Source outputLineSource Selects which internal signal or event driven pulse or
software control state to output on the selected line.
Note, the LineMode feature must be set to Output. The
List of supported output line sources is product-specific.
The
Event Control section provides details and timing
diagrams for the supported trigger modes.
1.02
Beginner
DFNC
Off Off Line output is Open
Software Controlled SoftwareControlled
The OutputLineValue feature changes the state of the
output
Pulse on: Start of Frame PulseOnStartofFrame Generate a pulse on the start of the Frame Active event
Pulse on: Start of Exposure PulseOnStartofExposure
Generate a pulse on the ExposureStart event. This
option is typically used to trigger a strobe light.
Pulse on: End of Exposure PulseOnEndofExposure Generate a pulse on the ExposureEnd event. This option
is typically used to trigger a strobe light.
Pulse on: Start of Readout PulseOnStartofReadout Generate a pulse on the ReadoutStart event.
Pulse on: End of Readout PulseOnEndofReadout Generate a pulse on the ReadoutEnd event.
Pulse on: Valid Frame
Trigger
PulseOnValidFrameTrigger Generate a pulse on the ValidFrameTrigger event.
Pulse on: Rejected Frame(s)
Trigger
PulseOnInvalidFrameTrigger Generate a pulse on the InvalidFrameTrigger event.
Pulse on: Start of
Acquisition
PulseOnStartofAcquisition Generate a pulse when the AcquisiontStart event occurs.
Pulse on: End of Acquisition PulseOnEndofAcquisition Generate a pulse when the AcquisiontStop event occurs.
Pulse on: End of Timer 1 PulseOnEndofTimer1 Generate a pulse on the TimerEnd 1 event.
Pulse on: End of Counter 1 PulseOnEndofCounter1 Generate a pulse on the CounterEnd 1 event.
Pulse on: Input 1 Event PulseOnInput1 Generate a pulse on the Input signal 1 event
Pulse on: Input 2 Event PulseOnInput2 Generate a pulse on the Input signal 2 event
Pulse on: Software
Command
PulseOnSoftwareCmd Generate a pulse on the input of a Software Command.
Exposure Active ExposureActive Generate a signal that is active when the Exposure is
active.