Dalsa Genie Nano-CXP Скачать руководство пользователя

Страница: 103 / 143

Genie Nano-

CXP Series™

Feature Descriptions

•

101

Updating Firmware via File Access in CamExpert

•

Click

on the “Setting…” button to show the file selection menu.

•

From the

File Type

drop menu, select the file

Type

that will be uploaded to the Genie Nano.

This CamExpert tool allows quick firmware changes or updates, when available for your Genie
Nano model.

•

From the

File Selector

drop menu, select the Genie Nano memory location for the uploaded

data. This menu presents only the applicable data locations for the selected file type.

•

Click the Browse button to open a typical Windows Explorer window.

•

Select the specific file from the system drive or from a network location.

•

Click the Upload button to execute the file transfer to the Genie Nano.

•

Reset the Nano when prompted.

•

Important: File upload rates are fixed (as per the CXP standard) at 20Mbits/s. As an example a
firmware file upload will take about 2½ minutes.

Overview of the

deviceUserBuffer

Feature

The feature

deviceUserBuffer

allows the machine vision system supplier access to 4 kB of reserved

flash memory within the Genie Nano. This memory is available to store any data required, such as

licensing codes, system configuration codes, etc. as per the needs of the system supplier. No Nano
firmware operation will overwrite this memory block thus allowing and simplifying product tracking
and control.

Содержание Genie Nano-CXP
















































































































































Результаты поиска

Содержание Genie Nano-CXP

Отзывы:

Похожие инструкции для Genie Nano-CXP

Бренды по названию

Популярные бренды

Dalsa Genie Nano-CXP, Руководство пользователя

Результаты поиска

Содержание Genie Nano-CXP

Отзывы:

Похожие инструкции для Genie Nano-CXP

Бренды по названию

Популярные бренды