DAELIM S2 125 Скачать руководство пользователя

Страница: 69 / 184

7-6

LH. CRANKCASE COVER/CONTINUOUSLY VARIABLE TRANSMISSION

MOVABLE DRIVE FACE INSPECTION

●

The weight rollers push on the movable drive face (by
centrifugal force); worn or damaged weight rollers will
interfere with this force.

●

Check the rollers for wear or damage and replace as
necessary.

●

Measure the O.D. of each roller, replace if the service
limit is exceeded.

SERVICE LIMIT : 19.5mm

●

Check the drive face boss for wear or damage and
replace as necessary.

●

Measure the O.D of the drive face boss. Replace the
boss if the service limit is exceeded.

●

Measure the I.D. of the drive face. Replace it if the
service limit is exceeded.

●

Movable drive face boss outer diameter.

SERVICE LIMIT : 23.960mm

●

Movable drive face inner diameter.

SERVICE LIMIT : 24.025mm

MOVABLE DRIVE FACE INSTALLATION

●

Install the weight roller on the movable drive face.

●

Install the ramp plate.

●

Apply the inside of the movable drive face with the
specified amount of grease.

SPECIFIED GREASE : ALVANIA EP2
GREASE APPLICATION : 0.5-1.5 g

●

Install the movable drive face boss.

Do not get the grease on the drive face. Remove any
misplaced grease with a degreasing agent.

Use only the specified grease in the specified amount.

WEIGHT ROLLER

RAMP PLATE

MOVABLE DRIVE FACE

WEIGHT ROLLER

MOVABLE DRIVE FACE

BOSS

Содержание S2 125

























































































































































































Результаты поиска

Содержание S2 125

Отзывы:

Похожие инструкции для S2 125

Бренды по названию

Популярные бренды

DAELIM S2 125, Руководство по обслуживанию

Результаты поиска

Содержание S2 125

Отзывы:

Похожие инструкции для S2 125

Бренды по названию

Популярные бренды