manualshive.com logo in svg

DAELIM S2 125, Руководство по обслуживанию

Поделиться
Скачать
DAELIM S2 125 Скачать руководство пользователя страница 118

11-7

TRANSMISSION/CRANKSHAFT/CRANKCASE

RH. CRANKCASE

LH. CRANKCASE

CRANKSHAFT

DOWEL PIN

RH. CRANKCASE

CRANK BEARING

UNIVERSAL 
BEARING PULLER

●

Remove the transmission bleeder tube.

●

Remove the RH./LH. radiator hose from the RH.
crankcase.

●

Face the LH. crankcase downward, and remove the
RH. crankcase from the LH. crankcase while tapping a
few places on the LH. crankcase with a plastic hammer.

CRANKSHAFT REMOVAL

●

Remove the crankshaft from the RH. crankcase by
using a crankshaft remover.

●

If the bearing is left on the RH. crankcase, use the
driver handle and the outer driver to remove it.

TOOLS : DRIVER

ATTACHMENT, 42 X 47 mm

●

If the bearing is left on the crankshaft, use a bearing
puller to remove it.

TOOL : UNIVERSAL BEARING PULLER

●

Remove the dowel pin and gasket.

·

Be careful not to distort the mating surface of the
crank case during removal.

·

After removing the crankshaft from the RH.
crankcase, replace the RH. crankshaft bearing with a
new one.

Содержание S2 125

























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды